648475
4
Zoom out
Zoom in
Previous page
1/76
Next page
2
SUBWOOFER REAR-PANEL CONTROLS AND CONNECTION
1) Power Mode:
When switched to 'Auto' position, the subwoofer will then be in Standby
mode. It will automatically turn on when an audio signal is detected and
will return to the Standby mode when no audio signal is detected after
approximately 10 minutes. Setting this switch to ‘On’ keeps the
subwoofer powered until Power Switch is turned 'Off.'
2) On/Standby LED:
When the Power Switch is in the ‘On’ position, this LED indicates whether
the subwoofer is in the On or Standby state.
• When the LED glows blue, the subwoofer is turned On.
• When the LED glows red, the subwoofer is in the Standby mode.
3) Phase Switch:
This switch determines whether the subwoofer transducer's piston-like
action moves in and out in phase with the main speakers. If the
subwoofer were to play out of phase with the main speakers, the sound
waves from the main speakers could partially cancel out the sound waves
from the subwoofer, reducing bass performance and sonic impact. This
phenomenon depends in part on the placement of all the speakers relative
to the listening position and to each other in the room.
4) Crossover Control:
This control determines the highest frequency at which the subwoofer
reproduces sounds. The higher you set the Crossover control, the higher
in frequency the subwoofer will operate and the more its bass will
“overlap” that of the speakers. This adjustment helps achieve a smooth
transition of bass frequencies between the subwoofer and the speakers
for a variety of different rooms and subwoofer locations.
5) Volume:
Use this control to adjust the subwoofer’s volume. Turn the knob
clockwise to increase the volume; turn the knob counterclock-wise to
decrease the volume.
6) Subwoofer (LFE Input):
Connect the subwoofer to the dedicated subwoofer / LFE output of a
receiver/processor.
7) Power Switch:
Set this switch in the ‘On’ position to turn the subwoofer on. If you will be
away from home, or will not be using the subwoofer for an extended
period, set this switch in the ‘Off’ position to conserve energy.
8) Power Input:
After you have made and verified the subwoofer’s input connection, plug
the power cord into an active, unswitched electrical outlet for proper
operation of the subwoofer.
DO NOT plug the power cord into the accessory outlets found on some
audio components.
SUB 100P
POWER
MODE
ON
PHASE
NORMAL
AUTO REVERSE
PWR
BLUE: ON
RED: STANDBY
CROSSOVER
50Hz 150Hz
MIN
MAX
VOLUME
SUBWOOFER
INPUT
POWER
ON
OFF
POWER
INPUT
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Arena SUB 100P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Arena SUB 100P in the language / languages: All languages as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info