756976
8
Zoom out
Zoom in
Previous page
1/12
Next page
ENGLISH USER MANUAL
JB SYSTEMS 6/7 Club7usb
CONTROLS AND FUNCTIONS (rear)
32. MAINS CABLE: connect this cable to a 230V/50Hz mains outlet. Before use, inspect the cable to be
sure it’s not damaged!
33. POWER SWITCH: Used to turn the power of the mixer on and off. The blue led (7) is lit when the mixer
is turned on.
34. MASTER BALANCED OUTPUT: The XLR-connectors can be used to connect this mixer to any
balanced amplifier input, using special balanced signal cables.
35. [BOOTH] OUTPUT: The “[Booth]” output carries the same signal but can be controlled independently by
the “[BOOTH]” (10). Use the output to connect unbalanced amplifiers.
36. RECORD OUTPUT: Carries the same signal as the master outputs but is not influenced by the master
level and balance controls. Used to connect analog recording equipment. You can also connect a
computer for direct digital recording on the USB1 connection (46).
37. INPUT CHANNEL 4: used to connect line level audio signals. The input source selector (3) on the front
determines which input will be active.
38. INPUT CHANNEL 3 (CD): used to connect line level audio signals. The input source selector (3) on the
front has to be put to “[CD]”.
39. INPUT CHANNEL 3 (USB2/PH): used to connect phono level audio signals. The input source selector
(3) on the front has to be put to “[PHONO/USB2]”. Press switch (47) on the rear of the mixer to select the
phono input.
40. USB1/PH SWITCH: This switch makes it possible to switch between the phono input (41) and the USB1
input (46) on channel 3.
41. INPUT CHANNEL 2 (USB1/PH): used to connect phono level audio signals. The input source selector
(3) on the front has to be put to “[PHONO/USB1]”. Press switch (40) on the rear of the mixer to select the
phono input.
42. INPUT CHANNEL 2 (CD): used to connect line level audio signals. The input source selector (3) on the
front has to be put to “[CD]”.
43. LINE INPUT CHANNEL 1 (LN): used to connect a line level audio signal to channel 1. The input selector
(3) on the front has to be put to “[LINE]”.
44. LINE INPUT CHANNEL 1 (CD): used to connect a line level audio signal to channel 1. The input
selector (3) on the front has to be put to “[CD]”.
45. USB CONNECTION [USB2]: USB connection (USB2 for CH3). You can connect any PC through this
USB connection. The PC/Mac will detect your mixer as a sound card, normally no drivers are needed.
46. USB CONNECTION [USB1]: bidirectional USB connection (USB1 for CH2). You can connect any PC
through this USB connection. The PC/Mac will detect your mixer as a sound card, normally no drivers
are needed. Since the USB port is bidirectional you are able to play music on your computer and mix this
music with other sources like CD, phono, etc. At the same time you can record your mix on your
computer with the same USB connection
47. USB2/PH SWITCH: This switch makes it possible to switch between the phono input (39) and the USB2
input (45) on channel 2.
48. GROUND (GND) CONNECTION: Many Turntables have a GND-connection. It is preferable to connect
this signal ground to the GND-connector. If your turntable does not have a ground wire, you don’t have
to use this connector.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JB systems CLUB7-USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JB systems CLUB7-USB in the language / languages: English as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JB systems CLUB7-USB

JB systems CLUB7-USB User Manual - German - 10 pages

JB systems CLUB7-USB User Manual - Dutch - 10 pages

JB systems CLUB7-USB User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info