616091
2
Zoom out
Zoom in
Previous page
1/4
Next page
Placement
Make certain the speaker is located between ceiling joists to avoid cutting into joists. Place the
supplied template a minimum of 5/8 from any joists. Draw a line around it to mark the cutout.
Take care when cutting the hole to avoid cutting into pipes or electrical conduits. If you encounter
pipes, electrical conduits or other obstacles you may have to select another location for the
speaker.
Installation
Before installing the speaker connect the speaker wires as described under Hookup.
Remove the grill from the speaker. First loosen screws A (fig. 1) by turning them counter clockwise.
Loosen all 4 screws until the Dog ears B (fig. 2) can move freely. Do not remove the screws.
Install the speaker into the ceiling and position it. Turn screws A clockwise until they are tightened
and the frame firmly installed.
Before reinstalling the grill on the speaker make adjustments as described under Adjustments.
Reinstall the grill. If the grill has a loose fit and/or is vibrating when the speaker is playing remove
the grill, install the supplied non-curing glue strips at locations C (fig. 1) and reinstall the grill.
Hookup
The receiver/amplifier must be turned OFF before you connect the speakers or it may cause
damage to the receiver/amplifier.
Connect the speaker wires from the receiver/amplifier to the speakers. When connecting the
speaker wires make sure that LEFT (L) is connected to LEFT (L), RIGHT (R) to RIGHT (R), POSITIVE
(+) to POSITIVE (+) and NEGATIVE (-) to NEGATIVE (-). If terminals are color coded, RED is POSI-
TIVE (+) and BLACK is NEGATIVE (-).
For dual voice coil models (designated by DVC in model number) connect LEFT (L) to one side
and RIGHT (R) to other side of speaker.
Adjustments
The tweeter can be tilted towards the listening area, due to high frequencies being more
directional than low frequencies. The impedance of the speaker and the level of the tweeter are
adjustable except on DVC models. Both adjustments are located on the front of the frame.
IMPEDANCE:
The factory setting is 8 ohm. If the receiver/amplifier specifies a minimum
impedance of 4 ohm, the speaker may be switched to the 4 ohm posi-
tion. This will make the speaker play louder. When installing more then 1
pair of speakers to a receiver/amplifier special care should be taken to impedance matching the
speakers to the receiver/amplifier. This may require impedance matching devices. Consult your
dealer for information regarding impedance matching.
TWEETER LEVEL:
The factory setting is 0 dB. The level of the tweeter can be lowered
by 3 or 6 dB to suite individual tastes in different room
environments. Experiment with the settings to find the preferred sound.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jamo 8.5CS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jamo 8.5CS in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info