488698
3
Zoom out
Zoom in
Previous page
1/31
Next page
4 5
6. Position the ring sensor on the centre of the telephone speak-
er.
Note: On most telephones the speaker is located underneath
the handset. If you are unsure of the speaker’s location, have
someone call you and note the precise location where the ring-
ing tone comes from.
7. Insert the AUX plug of the connector cord into the AUX socket
at the bottom of the base unit of your cordless headset.
After assembling the product, verify that the product is working cor-
rectly. Complete the following steps:
1. Set your cordless headset to headset mode by pressing the
multifunction/line button on your cordless headset or remote
unit.
If the product is working properly, the lifting arm will lift the
handset out of the telephone’s cradle and you will hear the dial
tone in the headset.
2. If there is no dial tone, adjust the lifting arm height with the
lifting arm height control. The + raises the lifting arm and the
- lowers the lifting arm.
Note: If you still do not hear a dial tone, extend the Lifter Arm
from its factory-set position.
Features and customisation
On-line indicator
The on-line indicator lights when your handset is lifted and you
have a dial tone, and fl ashes continuously when you have deacti-
vated the ring sensor.
Adjusting the Ring Sensor sensitivity
The ring sensor detects the telephone’s ring and is factory pre-set
to most standard telephones. The ring sensor may, however, need
adjustment to recognise a less common telephone ring tone. Raise
and lower the ring sensor’s sensitivity by adjusting the ring sensitiv-
ity control on the back of the unit.
The ring sensor is set correctly when the on-line indicator lights to
indicate an incoming telephone call. If the on-line indicator does not light when the tele-
phone rings, have someone call you and turn the ringer sensitivity control clockwise
until the on-line indicator is lit.
If you have unsuccessfully tried to increase ring sensor sensitivity, mount the external
ring sensor by completing the following:
1. Mount the plug of the external ring sensor to the external socket of the product.
2. Remove the protective fi lm on the external ring sensor and attach it as close as pos-
sible to the telephone’s speaker.
3. Readjust the ring sensor’s sensitivity if the on-line indicator does not light when an
incoming call is received.
Answering and making telephone calls
To answer a telephone call, press the multifunction/line button on
your cordless headset or remote unit. The product will then auto-
matically lift the handset and put the call through.
To terminate a telephone call, press the multifunction/line button on
your cordless headset or remote unit. The product will now lower
the telephone handset and terminate the call.
Note: When using your telephone in speakerphone mode, e.g. for
a conference call, deactivate the ring sensor by pressing the ring
sensor on/off button to the off mode. The on-line indicator will fl ash
when the ring sensor on/off button is in the off mode.
Press the ring sensor’s on/off button to the on setting when you
have completed your speakerphone call.
GN1000_contents.indd 4-5 11-03-2003, 14:15:14
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jabra GN1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jabra GN1000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info