Manual Jablotron WJ-80 (page 1 of 1) (English)

554844

Zoom out

Zoom in

1/1

The WJ-80 interface for an outdoor keypad / reader MKM51002

The WJ-80 interface for an outdoor keypad / reader

The WJ-80 is a component of Jablotron’s JA-80 Oasis 80 system. It is

designed to connect JA-80H outdoor keypads or JA-80N RFID readers to a

control panel. It provides an output to operate the electric strike of a door lock

and is equipped with a wireless door bell transmitter.

The WJ-80 can also be used to interface to a third party keypad (reader)

which uses Wiegand 26b protocol (e.g. HID RK-40 a RK-10).

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. It should be placed in a protected internal

part of a house (usually near an entrance door equipped with an electric

lock).

Open the front cover by unscrewing the screw and take out the electronic circuit

board (held by 2 tabs). Install the back part of the housing to the desired place, put

back the electronic circuit board and connect the cables – see the following diagram.

Do not connect the power before all wiring up and setting the DIP switches has been

finished.

Terminals

Tamper switch

1 2 3 4

DIP

switches

Terminals for

keypad

or reader

JA-80H

JA-80N

Termina ls

for

external lock

system

bus

OASiS

Control panel (C.P.) bus cable

+U, B, A, GND connect to the corresponding terminals in the C.P.

Keypad/reader cable – a max. of one JA-80H or JA-80N can be wired in

terminal wire

+12V red (power, max. 60mA)

D0 green (DO data of Wiegand 26b)

D1 brown (D1 data of Wiegand 26b)

TMP grey (TAMPER input, triggers if disconnected from GND)

BZR yellow (output to operate the keypad buzzer by grounding it,

max. 10mA)

GND blue and white (ground)

OPN unlock input – grounding this terminal activates the output

relay for a period selected by DIP switch # 3. Can be used as a

push button input to open the door from the inside.

A third party keypad/reader can be used if it uses Wiegand 26b protocol, but

Jablotron cannot guarantee its compatibility.

Electric door lock output

+E , GND a power supply to activate the electric strike of a door lock (its

long-term current is limited by a resistor and its initial energy

pulse is supplied by a reservoir capacitor). The power output

is optimised for door locks of the type Jablotron Z8-12V.

C and NO normally open dry contact of the output relay (max. 5A / 60V)

DIP switches

Interface features can be set by the DIP switches:

# OFF ON

the keypad (reader) works as a

control panel (CP) keypad. The

output relay can be activated by a

PGY output (if DIP #2 is on)

the keypad (reader) only operates

the door lock and starts a CP

entrance delay if the CP is set

(armed). The output relay is activated

by a valid code (card) entry on the

connected keypad.

2 no reaction to PGY output of CP relay reacts to the PGY output

3 relay energizes for 3 sec. relay energizes for 6 sec.

4 no entrance and exit beeps from

the connected keypad

exit and entrance beeps enabled*

* disconnect the yellow wire from the BZR terminal to switch the keypad’s acoustic

and optical indication off completely.

The connected keypad / reader function

For the WJ-80 to function properly, the control panel should have its back-up

battery connected. The basic function of the keypad / reader is determined by DIP

switch # 1:

OFF = the keypad / reader works as a control panel keypad and can therefore be

used to operate and program the alarm system. The output relay can only be

activated in this mode by the CP’s programmable PGY output (if DIP switch # 2 is

ON, the duration of relay activation is set by DIP switch # 3).

ON = the keypad / reader only operates the door lock (external bypass function). It

means:

The door lock opens by: a valid code (card) entry, grounding the OPN terminal and, if

DIP # 2 is on, then also by triggering the PGY output (this can be used to open the

door by entering ∗9 on the control panel keypad).

• If the door lock opens (by any of the above ways) while the alarm system is set, the

entrance delay will start (as if a delayed detector has just been triggered).

• When the external keypad / reader is in this mode it cannot be used to set, unset or

program the alarm system. It can however be used to program access codes

(cards) the same way as via the control panel keypad (by the ∗6 sequence).

• If operation of the control panel by the service code (sequence 6921 in the

control panel) is enabled, then the service code cannot be used for door

opening.

The JA-80H’s door bell button

The bottom left key on the keypad can be used as a door bell button if the

JA-80L wireless siren has been installed. If this function is desired, the button should

be enrolled to the JA-80L siren (by pressing it while the siren is in enrollment mode).

If the door bell button is used, the WJ-80 housing should not be shielded by any

metal which could block radio signals.

Configuring the keypad for operation with the WJ-80

If the JA-80H keypad or JA-80N reader is connected to an Oasis control

panel via a WJ-80 unit and it does not work as described above, then it is not

set to the correct (factory default) operational mode. In such a case, follow

the keypad / reader manual.

Example of wiring

Exit button

at building exit

electric

door lock

Z8-12V

JA-80H

keypad

JA-80N

reader

OASiS

system

bus

Specifications

Power via the control panel bus

Standby consumption approx. 60mA (incl.JA-80H or 80N)

Output relay contact max. 5A/60V

Built-in doorbell transmitter 868MHz, Oasis protocol

Operational environment II. indoor general, –10 to +40 °C (EN50131-1)

WJ-80 dimensions 76 x 110 x 33 mm

EN 50131-1, EN 50131-5-3 Grade 2

Can be operated according to ERC REC 70-03

FCC ID VL6WJ80

Jablotron Ltd. hereby declares that the WJ-80 is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC and complies

with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept

any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could

void the user´s authority to operate the equipment. The original of the conformity

assessment can be found at www.jablotron.com

, Technical Support section.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron WJ-80 in the language / languages: English as an attachment in your email.

The manual is 0,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron WJ-80 Manual

Product: