555019
1
Zoom out
Zoom in
Previous page
1/2
Next page
Wireless Control Receiver UC-215 1/2 MEJ51400
Wireless Control Receiver UC-215
Description
The UC-215 is a three channel receiver of coded signals.
The status of two output relays and the output transistor is
indicated on the front panel. Up to 20 remote controls
(RC-10) can be taught to the unit. There are three different
operating modes available for each remote control.
The UC-215 can be used for control of alarm systems,
remote gate opening, garage door control, panic switch etc..
A floating code ensures a high security of transmission.
An external antenna (included) can be used as well as the
built-in antenna.
Specification
Operating voltage: 11-14 V DC
Power consumption: standby 5 mA
max. 45 mA (both relays activated)
Operating frequency: 433.92 MHz
Coding: digital, each remote control or detector
has a unique floating code
Output relays: max. 120V/1A
Output transistor: max. 12V/0.2 A
Range (open area): with RC-10 up to 30 meters
External antenna CINCH connector, 50 Ohm
Designed for indoor use only.
Installation
Open the external cover of the unit by pressing the lock on
the top. Loosen the central screw and take out the PCB. Route
wires through the hole in the bottom of the rear housing. Attach
the housing to the desired place using screws.
Terminal description:
NC, NO, C output relay dry contacts
TAMPER tamper switch output (max.12V/50mA)
OUT output of NPN transistor switching to GND
+12V, GND power voltage
Setting
Remote controls enrolling - you
can teach up to 20 different RC-10 remote
controls to the UC-215 unit. There are two
buttons on each RC-10 (A and B),
enabling each remote control to send
three different commands by pressing
button A, B or A & B simultaneously.
There are two setting buttons in the
UC-215. Button X is used for relay X
teaching, button Y is used for relay Y
teaching. By pressing the setting button
you can scroll through the three learning
(operating) modes (1 to 3) indicated by a corresponding
flashing indicator.
By pressing a button on the remote control while a desired
UC-215 learning mode is selected, you teach that button to the
receiver’s memory. The corresponding operating mode will now
be associated to this remote control button
Operating modes available (valid for X and Y relays)
MODE reaction of the relay
when RC button pressed
which RC -10
button can be
taught
1 pulse
relay will turn on for 1 second A, B, A&B
2 latch
relay status will change to the
opposite (ON/OFF/ON...)
A, B, A&B
3 ON - OFF
button A will turn relay on, button
B turn relay off
A or B
Setting remarks
new RC buttons are added to already taught ones
after 20 RCs are taught, no other remote can be added
double flash of LEDs indicates full memory
if one button is taught for multiple modes, only the last
taught mode will remain in the UC-215 memory
you can combine different modes for different RC buttons
the output OUT will be activated only by simultaneous
pressing of A&B buttons on a remote control, which A
button was learn for X relay and B button for Y relay. The
OUT mode is the same as selected mode of relay X. This
way three independent outputs can be controlled.
selected setting mode will close after a RC button is taught,
or automatically after 10 seconds
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron UC-215 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron UC-215 in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info