This thermostat can replace a common indoor residential thermostat.
It can be used with receivers produced by Jablotron such as the
UC-222, UC-6007, UC-6014 etc.). It is designed to be used with
electrical, gas or oil heating systems. The temperature adjustment can
be done very simply by turning a setting knob. The main advantage is
that there is no need for a cable between the thermostat and the
heating system.
Installation
The TP-31 should be mounted in a
dry indoor location. Choose a mounting
location about 1.5 meters above the
floor in an area with good air
circulation. Avoid places with draughts,
dead air spots and radiant heat from
the sun or appliances. It should not be
installed close to any metal structure or
other objects that may obstruct radio
signal transmissions
1. Remove the front housing of the
thermostat by gently pressing the tab
on the right side (using a screwdriver).
2. Attach the thermostat to desired
position on the wall with the two
screws
.
3. Insert the battery.
4. Close the thermostat.
Mounting the UC-222 receiver unit
Note: only a qualified technician should provide installation and servicing.
Place the receiver unit in a suitable place near the heater. Wiring the unit
to the heater should only be done by a professional electrician.
1. Release the upper cover by
pressing the plastic tab on the
top side of housing.
2. Release the internal cover (1
screw).
3. Mount the unit to the desired
location (2 screws).
4. Connect power 230VAC/50Hz
to terminals L and N.
5. Two PE terminals are available
for a protective earth
connection.
6. Terminals C (common), N.O.
(normally open) and N.C.
(normally closed) are outputs
of the relay contact. This
contact is protected by a 6.3A fuse. The contacts are galvanically
separated.
Note: A built-in LED indicator indicates the status of the output relay
Temperature setting
The desired temperature can be set simply by turning a knob placed on the
top of the thermostat. If the set temperature is higher then actual temperature in
the room the red indicator on the thermostat will lit for 3 seconds after turning the
knob.
If it is set to À (anti-freezing mode), the thermostat will keep the temperature
at 6 ˚C ±0.5˚C.
The information to the receiver unit is sent in about 5 seconds after setting the
desired temperature. The LED on the receiver unit indicates heating.
Low battery
If the yellow low-battery indicator on the lower right corner of
thermostat is flashing, replace the battery.
Enrolling the thermostat to the receiver unit
The thermostat can be enrolled to the receiver unit in the following
way:
1. Remove the battery from the thermostat for 1 minute.
2. Remove the upper housing from the receiver unit.
3. Keep pressing the button inside the receiver until the 4th LED starts
flashing.
4. Insert the battery into the thermostat. The LEDs in the receiver will
flash once to confirm enrollment.
Note:
If the thermostat is delivered as a kit with the UC-222 receiver (TP-31 SET),
then it has already been pre-enrolled to the receiver unit in the factory, so it
is not necessary to enroll it again.
Each receiver unit can work with up to 8 thermostats. If any other device
(remote control etc.) has been enrolled to the receiver, the receiver must be
reset before enrollment of the thermostat. To reset the memory, make the
4th LED flash by pressing the button, and then press and hold the button
until all LEDs flash rapidly.
7340
73
45
Specification
Thermostat TP-31
Power supply: 1x AA 1.5 V alkaline battery
Temperature Accuracy: ±0.5 ˚C
Temperature Measurement: 6 ˚C and 14 - 28˚C
Working frequency:433.92 MHz
Coding: Digital, each thermostat has a unique
floating code
Working distance up to 100 m (open area)
Working temperature: -10 ˚C to + 50 ˚C
Dimension: 73 x 40 x 73 mm
Receiver unit UC-222
Power supply: 230 V AC 50 Hz, protection class II
Power drain: 1 VA (0.6 W) standby 1.8 VA (1 W) relay switched on
Frequency: 433.92 MHz
Coding: digital, each thermostat has a unique
floating code
Output relay: over switching dry contact, fused 6 A at 250 V
Can be operated according to ERC REC 70-03
Jablotron Ltd. hereby declares that the TP-31is in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC.
Original of the conformity assessment can be found at the web page
www.jablotron.com
, section Technical support.
Note: Dispose of batteries safely depending on the type of the batteries and local
regulations. Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the manufacturer after
use.
2
1
3
4
230 V
AC / 50 Hz
output
Relé
max. F6.3 A / 250 V
setting
button
L
PE
C NC NO
PE
N
indicators
desired temperature
low battery
Internet: www.jablotron.com
tel.: 483 559999
fax: 483 559 993
Pod Skalkou 33
466
01
Jablonec
nad
Nisou
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron TP-31 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron TP-31 in the language / languages: English as an attachment in your email.
The manual is 0,11 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
