The RC-86 is a component of Jablotron’s OASiS 8x series alarm systems. It is designed to
remotely control setting/unsetting, trigger panic alarms, and control other appliances. The big
advantage is the possibility of configuring it to 433 MHz (JA-60 systems, UC-216, UC-222
receivers etc). The keyfob indicates its flat battery. A two button version of the case is also
available. Contact your dealer.
Enrolling to an Oasis control panel
A pair (left or right side) of the keyfob buttons can be enrolled to a control panel by pressing and
holding both buttons. See the OASiS control panel installation manual for more details.
If you wish to remove the keyfob from the system, erase it from its address in the control panel.
The natural reaction of the pair of buttons is setting and unsetting for each button respectively,
and panic alarm triggering by pressing both buttons together. If a reaction other than natural is
assigned, the reaction will only be triggered by buttons
or (according to which pair was
enrolled).
If you enroll both pairs of buttons to two different addresses in the control panel, then different
reactions and sections can be assigned to each pair of buttons. Then, for example, one pair could
set/unset the complete system, and the other pair could be used for partial setting.
Remaining buttons can be used to control another device such as e.g. a Jablotron car alarm, or
UC-8x and AC-8x receivers, UC-216, UC-222 …
Locking the keyfob
If four buttons version of the keyfob is used, keys can be locked or unlocked by pressing a
diagonal button pair (
+ or +). When the keys are locked, the keyfob LED flashes rapidly
if any button is pressed (no signals are sent under these conditions). See the Keyfob configuration
chapter.
Panic alarms
Panic alarms can be triggered when buttons +
or
+
are pressed simultaneously. The keyfob
can be set so that a panic alarm is triggered when any one button on the keyfob’s left side (even
or)
is pressed. See the Keyfob configuration chapter.
Using with other products
In addition to Oasis control panels, the keyfob can also be used with other Jablotron products that
communicate via Oasis protocol. Examples are relay receivers type UC-8x and AC-8x. Guidance
on using the keyfobs can be found in the manual of the desired receiver.
If you want to use the keyfob for 433 MHz a pair of keys can be switched to this mode. See the
configuration chapter.
Keyfob configuration
1. Press and hold
.
The keyfob flashes
once and after a while starts to light
continuously.
2. Keep
pressed while pressing
x-
times according to the table below.
3. Then release
to end configuration
mode.
4. As confirmation, the LED flashes the
same number of times as you pressed
the
button.
The default mode is 5: No lock - unlock
possible, no one-button PANIC possible,
both pairs are 868MHz
Battery replacement
Indication of a flat battery is provided by
the keyfob LED. After any button is pressed
the LED flashes long (as usual) and then
briefly flashes twice as an indication of a flat
battery. The keyfob works as usual, it’s just that the working range of the keyfob could be reduced.
This indication is also done on the control panel (on its keypad or communicator). The indication is
cancelled when a new battery is inserted (L1016 type).
Expired batteries should not be thrown into the garbage, but disposed of according to local regulations.
Technical parameters
Voltage: alkaline battery type L1016 (6.0 V)
(Power Supply type C acc.to EN 50131-6)
Typical battery lifetime approx. 3 years (5 daily activations)
Communication band: 868 MHz/433MHz
Communication range approx. 30 metres (open area)
Op. environment acc. to EN 50131-1 II. indoor general
Operational temperature range -10 to +40 °C
Security grade acc.to EN 50131-1 2
Can be operated according to ERC REC 70-03
Complies with ETSI EN 300220,EN 55022, EN 50134-2, EN50130-4, EN60950-1
JABLOTRON ALARMS hereby declares that the RC-86is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.. The original of the conformity assessment can be
found at www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return the product to the
dealer or directly to the producer after use.
MGE53602
function
mode
x
pressed
keyfob
lock
or
PANIC
433MHz
433MHz
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron RC-86 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron RC-86 in the language / languages: English as an attachment in your email.
The manual is 0,03 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
