5 – production code; 6 – CR2032 battery (remove the
battery by pressing it in the direction of the arrow).
Keyfob enrolling to an Oasis control panel
The keyfob can be enrolled to a control panel
by pressing both buttons simultaneously. The
control panel must be in enrollment mode.
Detailed instructions can be found in the Oasis
control panel installer’s manual. The keyfob can
also be enrolled to the system by keying in a
serial number (5) which is on the bottom of the
keyfob.
Notes:
If you want to remove the keyfob from the
system (e.g. when you have lost it) delete it
from the corresponding address in the control
panel.
The natural reactions of the pair of buttons
include setting, unsetting and panic alarm
triggering (by pressing both buttons
simultaneously). If a reaction other than
natural is set in the control panel this reaction
will only be triggered by button (2).
Using the keyfob with other products
In addition to Oasis control panels, the keyfob
can also be used with other Jablotron products
that communicate via Oasis protocol (e.g. UC-8x
and AC-8x relay receivers).The keyfob is also
compatible with CA-1802A / 1803A and CA-340
car alarms. Keyfob application details can be
found in the manual of the desired product.
Button lock (child lock system)
Buttons can be locked (blocked) against
unwanted pressing – a keyfob child lock. The
button lock is not enabled as a default. When a
button is pressed, a control command indicated
with a short flash of the LED (1) is sent
immediately. To activate the button lock press
and hold button (3). The LED (1) first flashes
briefly and then lights up again after 3s. When
the LED is on, press button (2) twice quickly.
Release both buttons then. The LED (1) flashes
twice in confirmation. To deactivate the button
lock, repeat the above-mentioned procedure.
The LED (1) flashes once in confirmation.
If the buttons are locked, control commands
can only be sent by pressing the relevant
button twice rapidly.
The double click control commands (panic
alarm, keyfob enrolling) are not blocked by the lock.
Keyfob battery replacement
The keyfob indicates low battery status by
several rapid flashes of the LED instead of one
short flash when a button is pressed. The keyfob
keeps working but its operating range decreases
gradually. The low battery indication ends when
a new battery (CR 2032 type) is inserted. A low
battery is also indicated at the security system
control panel (on the keypad, by a
communicator). The keyfob can be opened by
unscrewing the three screws holding its rear
cover.
Do not throw used batteries into ordinary
household waste. Dispose of them at authorized
collection points.
Technical specifications
Power supply lithium battery type CR 2032 (3.0 V)
(Power supply type C acc. to EN 50131-6)
Battery lifetime approx 4 years (5 activations a day)
Communication band 868 MHz
Communication range approx 30 m (direct visibility)
Environment according to EN 50131-1 II indoor general
Operating temperature range -10° to +40°C
Classification according to EN 50131-1 Grade II
Can be operated according to ERC REC 70-03
Conformity ETSI EN 300220
EN 50130-4, EN 55022, EN 60950-1
JABLOTRON ALARMS a.s. hereby declares that the
RC-82 wireless keyfob is in compliance with the
essential requirements and other relevant provisions
of Directive 1999/5/EC. The original of the
conformity assessment can be found at
www.jablotron.com - Technical Support section
Note: Although this product does not contain any
harmful materials we suggest you return the product
to the dealer or directly to the producer after use. For
more detailed information visit www.jablotron.com.
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron RC-82 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron RC-82 in the language / languages: English as an attachment in your email.
The manual is 0,06 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
