554794
1
Zoom out
Zoom in
Previous page
1/2
Next page
The JK-84 “Oasis” wireless alarm kit 1 / 2 MKE59901
The JK-84 “Oasis” wireless alarm kit
Installation of the JK-84 kit shall only be undertaken by technicians
holding a certificate issued by an authorized distributor. This simplified
installation manual only describes the basics, for more details see the
manuals of particular devices.
1. Factory-default pre-enrolled devices
Address Device Note
03
JA-81M door
detector
Delayed reaction
04 JA-80P PIR detector Delayed reaction
48 RC-86 keyfob
Buttons and pre-enrolled
49 JA-80F keypad unit
Connect a magnetic door sensor
to its IN input.
50 JA-80L indoor siren
With an RC-89 wireless door-bell
button pre-enrolled.
JA-82KR Pre-enrolled to the JA-80L
2. Control panel and keypad installation
1. Attach the Control Panel (CP) to the desired location.
2. Connect back-up battery to the CP (attach it securely with
adhesive tape).
3. Connect the mains to the CP – its green LED will start flashing
4. Connect up the batteries in the JA-80F keypad service mode
should be displayed (if not, disconnect the keypad batteries, check
that the control panel is powered up and reconnect the keypad
batteries).
o Keeping the key pressed while connecting the keypad batteries
will open the keypad’s internal menu which allows you to select
the desired language (English = 1), to exit this menu press the #
key.
o If you exit Service mode accidentally, it can be re-entered by
keying in 0 8080.
o Close the keypad’s flip cover to save the battery while in the
service mode.
Before attaching the JA-80F keypad, test that it functions correctly at
the desired location. We recommended wiring up a magnetic door
sensor (provided with the kit) to the keypad’s IN input. This will ensure
that the keypad is “woken up” whenever the door is opened (to indicate
system status, to make entrance delay beeps and to have the access
card reader ready for reading cards).
3. Installing the detectors and the siren
1. Install the JA-81M magnetic detector, select its reaction via the
internal DIP switch (INS/DEL), connect its battery up and close the
cover.
2. Install the JA-80P PIR motion detector about 2 to 2.5 meters above
the floor, select its reaction via the relevant internal DIP switch
(INS/DEL), connect its battery up and close the cover.
3. Plug the JA-80L siren into a mains power socket.
IN 2
IN 1
GND
TMP
1k
mag.senzor
ON/OFF
Reaction
tamper
switch
external
senzor
Main board
Transformer
Back-up battery
Mains terminal
Digital bus connector
Tamper switch
LED
Antenna connection
01
02
COM
03
04
EW
IW
PGX
PGY
GND A B
+U
RESET
1234
ON
OFF
Radio module
Antenna
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JK-84 Oasis at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JK-84 Oasis in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info