554818
1
Zoom out
Zoom in
Previous page
1/2
Next page
The JA-89P wireless motion detector 1/2 MKU51102
The JA-89P wireless outdoor PIR detector
The JA-89P is an outdoor intruder detector designed to detect human body
movement in a protected area. It supplements a double-zone PIR sensor
produced by Optex with a Jablotron transmitter enabling the sensor to be
used within JA-80 OASiS systems. Both the PIR sensor and the transmitter
are powered by a lithium battery. Sharing the power source allows low voltage
reports to be transmitted to the control panel in the standard way. The
detector is equipped with two tamper sensors (front and back) capable of
signalling that the detector’s cover has been opened or that the detector has
been torn off its position. Self testing is performed automatically on a regular
basis including reporting detector status to the control panel. These properties
make the JA-89P a standard component of Jablotron’s OASiS system.
Installation
Choose a proper place for detector installation according to the following:
1. Install the detector perpendicular to the ground to make the upper
detection area parallel to the ground.
2. The installation height is 0.8 – 1.2 m.
3. Mount the detector so that the majority of traffic flow is across the
detection pattern.
4. Avoid positions where moving or waving objects like cars, plants or trees
might appear in the detection area. Avoid positions where the detector
can be affected by strong light sources, e.g. reflected sunlight.
3.1.1. 3.
0.8
1.2 m
Installation, step by step:
1. Unscrew the lock screw located on the bottom side of the upper cover and
remove the cover.
2. Unscrew the screws fastening the optical part of the detector and remove
this part by tipping it up.
3. Disconnect the rear tamper sensor cable.
4. You can fix the detector to an even plate using either two non-skimmed
holes or four skimmed holes located in the corners of the rear cover.
5. Use the drilling template supplied in the package for marking all the spots
relevant to detector fixing as well as to fixing the rear tamper magnet.
6. Alternatively, you can install the detector on a pole (Ø 43 – 48 mm) using
straps supplied with the package. However, this way of installation
disables the rear tamper switches (tear-off signalling) – you have to short
out the transmitter tamper inputs using a jumper.
7. After the bottom plastic cover has been fixed, insert the rear TAMPER
connector into the terminal marked TMP IN.
Caution: Never touch the detection surface of the PIR sensor.
Optical part
Upper cover
Lock screw
Fixing part
Adjustment switches
Rear tamper connection
Powering up and enrollment
The transmitter of wireless communication signals is located below the
detector’s optical part. Study the installation manual of the receiver (control
panel) first to learn how to enter enrollment mode. Only use a lithium battery
of type AA 3.6 V. The correct battery position is marked on the battery holder.
After a battery is inserted the transmitter sends an enrollment signal to the
receiver. The control panel – if used as a receiver – must be in enrollment
mode. You can use the detector’s switch No. 2 to configure control panel
reactions (ON = Instant, OFF = Delayed). Switch No. 1 should be OFF.
Rear tamper
connection
Switch No. 1
INSTANT
DELAYED
Switch No. 2
PULSE*
STATE
Vcc
TMP
INP
GND
detector
connection
LED
Set to
pulse mode
*
LITHIUM
3.6V AA
The JA-89P detector transmitter
Optical part adjustment
The detector’s optical part contains two PIR sensors each having its own
detection plane. The detection area angle of the lower sensor can be
configured over a wide range. The sensors operate with AND logic: an alarm
signal is generated only if both sensors are triggered (if both detection planes
are crossed). You can adjust the detection plane slope of the lower sensor by
a shifting lever according to the picture below.
A
distance 0 - 12 m
D
distance 0 - 2 m
C
distance 0 - 5 m
B
distance 0 - 8 m
The following table provides a summary of detection length
characteristics:
The lower sensor max. detection length
Position
Standard See note below:
A 10 m 8.0 to 12.0 m
B 8 m 6.0 to 10.0 m
C 5 m 4.0 to 5.5 m
D 2 m 1.5 to 2.5m
Note: The maximum detection length of the lower detection plane may
vary as above due to environmental thermal conditions. This must be
taken into consideration during detection range adjustment.
Protected area
Positions A,B,C,D
Unprotected area
Tolerance
The detection area angle is 90°. The direction can be adjusted in 15° steps
by rotating the detector’s plastic part. The detector lens covers the whole
angle of 180° - therefore it does not require any adjustment.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-89P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-89P in the language / languages: English as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info