631258

Jablotron JA-82Y GSM communicator Manual

13
Zoom out
Zoom in
Previous page
1/13
Next page
The JA-82Y GSM communicator installers manual 13/13 MDL51108
Tab. 7 communicator programming sequence continues
Function Sequence Possible options Factory default settings
ARC main telephone number / IP address
/ URL
01 p xx..x ∗0
p=1 ARC1, p=2 ARC2, p=3 IMG, xx..x = tel.
number max. 30 digits. When using IP protocol, IP
or URL addresses are entered instead of
telephone numbers – see URL command
To erase the corresponding telephone numbers or
URL addresses enter 01p*0
erased
ARC backup telephone number / IP
address / URL
02 p xx..x ∗0
p=1 ARC1, p=2 ARC2, p=3 IMG, xx..x = tel.
number max. 30 digits. When using IP protocol, IP
or URL addresses are entered instead of
telephone numbers – see URL command
To erase the corresponding telephone numbers or
URL addresses enter 02p*0
erased
Main ARC URL address setting
See ARC main telephone number / IP address / URL
Performed via OLink software or by SMS instruction code URL p xxxxxxx : pppp where p=1 ARC1, p=2 ARC2, p=3 IMG, xx..x =
URL address, pppp = port address (not required).. SMS instruction example: URL 1 www.arc1.com : 08080 To erase the
addresses key in 01p∗0, 02p∗0 or ARC telephone number
Installation (alarm system) ID for ARC use
03 p zz..z∗0
p=1 ARC1, p=2 ARC2, p=3 IMG, xx..x =
installation number max. 8 characters 0 to 9 and
∗1=A to ∗6=F
0000
Selecting the ARC communication
protocol
04 p x
p=1 ARC1, p=2 ARC2, p=3 ARC3(IMG)
x=0 CID,
x=1 Jablotron IP,
x=2 Jablotron SMS,
x=5 IMG – Jablotron image server
1 Jablotron IP
2 Jablotron SMS
Selection of events to report to ARCs 05 p uu x
p=1 ARC1, p=2 ARC2
uu is an event code (see 7.4)
x=1 report, x=0 no report
All events are reported - see tab. 3
Periodic or fixed ARC connection check 06 p x
p=1 ARC1, p=2 ARC2
x=0 with a period from the last report according to
the 07 p hhmm setting
x=1 once a day at the time set by entering 07 p
hhmm
With a period after the last report (X=0)
ARC communication checking period 07 p hhmm
p=1 ARC1, p=2 ARC2
hhmm = hours, minutes, see setting via 06 p x
2359
Enable ARC reporting (ARC2 backs up
ARC1)
08 p x
p=1 ARC1, p=2 ARC2
x=0 reports disabled, x=1 reports enabled,
x=2 only for ARC1, sets that ARC2 backs up
ARC1
1,2 ARC reporting disabled
3 enabled (IMG)
Recording reports sent to ARCs in the
control panel memory
001 x
x=0 no (only records ARC communication faults)
x=1 yes (all reports except communication checks)
no
Indicate an ARC communication fault if a
report is not successfully received within
110 sec of transmission
002 x
x=0 no
x=1 yes
no
Remote access password
894 xxx …x ∗0
1-32 characters, (only numbers are available when
using keypad)
1234ABCD
Locking the ARC settings
091 xx..x∗0
xx..x is your code (4 to 8 digits)
Entering this code and then exiting service mode
will lock the ARC settings
091*0 will erase the code (permanently unlocked)
unlocked
Unlocking the ARC settings
092 xx..x∗0
xx..x is the locking code used by sequence 091
ARC programming can be temporarily enabled in
service mode by entering this sequence. It will then
relock on exiting service mode. For permanent
unlocking see sequence 091.
Period of waiting before repeating
unsuccessful communication to the ARC
0001 p mmss
p=1 ARC1, p=2 ARC2
mmss = minutes, seconds
0015
Number of repeated attempts afte
unsuccessful communication to the ARC
0002 p n
p=1 ARC1, p=2 ARC2
n= 1x to 9x
2x
… 13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-82Y GSM communicator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y GSM communicator in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator User Manual - English - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info