555059
11
Zoom out
Zoom in
Previous page
1/13
Next page
The JA-82Y GSM communicator installers manual 11/11 MDL51108
12. Summary of all communicator texts for SMS messages and instructions
n factory default text: n factory default text: n factory default text:
0 Your system is reporting: 502 Delayed loop alarm 549 Master code changed
1 Device 503 Fire
550 The message has been transmitted by the
communicator.
2 Device 504 Panic alarm 551 Message transmission failed
. 505 Searching for a code 552 Service request
. 506 Alarm after powering up the system 553 PgX output ON
50 Device 507 Tamper alarm 554 PgX output OFF
201 Control panel 508 End of temper alarm 555 PgY output ON
202 Service code 509 End of alarm indication 556 PgY output OFF
203 Service inspection request 510 Alarm cancelled by user 601 SET
204 Communicator 511 Setting 602 UNSET
205 Keypad 512 Unsetting 603 STATUS
206 ARC code 514 Codeless setting 604 MEMORY
300 Master code 515 External communication fault 605 PGX ON
301 Code 516 External communication restored 606 PGX OFF
302 Code 517 Fault 607 PGY ON
. 518 Fault removed 608 PGY OFF
. 519 Mains dropout over 30 minutes 611 CREDIT
350 Code 520 Mains dropout 612 TXT
400 System status: 521 Mains recovery 613 PRG
401 Set 522 Battery discharged 614 GPRS
402 Unset 523 Battery OK 615 GSM
403 Exit delay 524 Switching to service mode 616 URL
404 Entrance delay 525 Leaving service mode 701 Enrolling
405 Alarm: 528 Radio jamming present 702 Finish setting
406 Service mode 529 Internal communication error 703 Signal strength
407 Maintenance mode 530 Internal communication restored 704 Control
409 Battery discharged 531 Communication test 705 Bypass
410 Tamper alarm 532 Unconfirmed alarm 706 Test OK
411 Alarm memory 533 Blocking after an alarm 707 Test error
412 Fault 534 Unblocking after an alarm 708 0/4
413 Power supply fault 535 Partial setting A 709 1/4
414 Unknown device status 536 Partial setting B 710 2/4
415 Time: 537 Partial setting AB 711 3/4
416 Last event: 538 Partial unsetting A 712 4/4
417 Unknown credit 539 Partial unsetting B 713 Code
418 Credit 540 Communicator failure 714 Text modification
420 Error while processing command 541 Communicator OK 715 Current detector
421 Output ON 542 Control panel battery failure 716 Service inspection
422 Output OFF 543 Control panel battery OK 717 Active output
423 Partially set A 544 Alarm 24h 718 Active detectors
424 Partially set B 545 Low credit balance 720 OASIS JA-80
425 Partially set AB 546 Power supply ON 721 Codes
426 SMS instruction processed successfully 547 Control panel reset
501 Instant loop alarm 548 Master code reset to 1234
tab. 6 table of factory-default SMS report and instruction texts
Notes:
The communicator always automatically puts numbers from 01 to 50 in front of Device or Code names
Texts 0 to 556 are used to create SMS event reports
Texts 601 to 616 are SMS instructions (to control the system remotely by SMS)
Texts 700 to 721 are used by keypads
Other texts are part of system configuration and are set in the OLink application
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-82Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y

Jablotron JA-82Y User Manual - English - 8 pages

Jablotron JA-82Y User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info