555059
3
Zoom out
Zoom in
Previous page
1/8
Next page
JA-82Y user manual - 3 - MLD51300
Remote control by phone
For a mobile phone, there are two ways to control the system remotely. You can either send SMS
instructions or establish an authorized connection (protected by an access code) to the system. In this
case the system is controlled by a voice menu. Press 9 to switch the phone to alarm keypad
simulation. The phone keypad can be used the same way as the system keypad. Using a fixed line
phone, you can only operate the system by dialling the communicator’s number and establishing an
authorized connection.
The below described way of remote control corresponds to the communicator’s factory default
setting. The configuration can be modified during installation. The installer should clearly explain
any changes to the default setting.
1. General rules for remote control via SMS instructions
More than one instruction can be used in a single SMS message. It has to be separated by a comma.
SMS instructions are not case-sensitive. Only standard English (ASCII) characters are accepted.
All SMS instruction words (parameters) must be separated by a space. In this document a space in an
SMS instruction will also be denoted by the underline character ‘_’.
SMS instructions can be sent from a mobile phone or from a GSM gateway.
If the % character is used, all preceding text will be ignored. The %% symbol ends processing when
used in SMS text – i.e. all the following text will be ignored. It is recommended to use this symbol at
the end of the instruction if the provider sends some additional text after your message
(advertisements etc.).
Warning: If any extra text is not separated from a valid SMS instruction text by % or %%
symbols, the SMS message will not be recognized and no instruction will be executed.
Performance of the instruction is confirmed by an SMS reply.
The default instruction texts can be customized by an installer or administrator. E.g. the command
PGX ON can be changed to SWITCH ON HEATING etc.
2. Setting (arming) by SMS xxxx_SET
The SET instruction allows you to put the system in to a set (armed) state, fully or partially. If the
system is already set, it will not change its status.
Send an SMS message containing:
xxxx_SET
where: xxxx is a valid access code (user or master)
_ is a space character
Example: Sending 4321 SET will set the system the same way as if the code 4321 had been entered
on the system keypad.
Notes:
As a factory default, setting (arming) by a SET instruction is confirmed by the system via an SMS
reply.
When the current system status does not allow system operation (e.g. when in programming mode),
you will be notified about the situation via an SMS reply.
In a split system, an xxxx_SET instruction will only have an effect on the section to which the code
xxxx belongs.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-82Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y

Jablotron JA-82Y Installation Guide - English - 13 pages

Jablotron JA-82Y User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info