Manual Jablotron JA-82M (page 1 of 1) (English)

554813

Zoom out

Zoom in

1/1

The JA-82M wireless magnetic door-detector 1 MCK52000

The JA-82M wireless magnetic door-detector

The JA-82M is a component of Jablotron’s Oasis 80 alarm system. It is

designed to detect opening windows, doors etc. It can be installed into plastic

or wooden frames and is suitable for most types of fitting. The battery-powered

detector communicates via OASIS radio protocol.

Installation preliminaries

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor.

The detector must not be exposed to bending or other deformation,

otherwise it can be damaged.

The product should be installed into a gap between the moving and non-

moving parts of windows or doors where the closing mechanism of a fitting is

located.

In practice, there exist various window/door frames and fittings. It is

therefore wise to verify before installation that the detector fits the given

window/door type. In the case of a wooden frame with too narrow a profile it is

usually possible to mill out a groove for detector insertion.

This detector reacts to the removal of its magnet unit. The electronics

should be installed onto the non-moving part of windows or doors, and the

magnet onto the moving part. If the supplied magnet does not exactly match

the window/door construction you can call the window/door supplier for a

magnet of a suitable type. Alternatively, you can adjust the magnet’s position

using a suitable back-plate.

Installation

11223344

ONON

12 34

OFF

CR 2354

190

3-5

1. magnet; 2. rear tamper sensors; 3. cover tamper sensor; 4. DIP switches;

5.battery; 6. led indicator; 7. adjustment lines; 8. fixing holes

LED indicator – 15 minutes after closing the detector’s battery cover, the LED

indicates detector triggering (a flashing light indicates window opening, a long

light indicates that both rear tamper sensors have been triggered).

1. Find a suitable place for the detector’s location so that the magnet is aligned with

the A (or B) adjustment line when the window/door is closed. After opening the

window/door, the magnet’s distance from the detector should increase by at

least 2 cm.

2. Avoid locating the detector directly on a metal frame as metal influences the

functioning of the magnetic sensor and radio communication. This can be

usually achieved by placing the detector on the hinge side of the window/door. In

addition, avoid installing the detector onto the bottom part of the window/door

frame due to possible water condensation.

3. Screw the magnet onto the moving part of the window according to the following

picture. Use a non-metallic back-plate if the frame groove is too wide.

3-5mm

10-15mm

4. Unscrew the battery cover and screw the detector on so that the magnet is

aligned with the A (or B) adjustment line when the window/door is closed, see

the picture. Be careful not to use too much force while screwing on, otherwise

the detector’s plastic body could be damaged.

5. You can use the long plastic plates supplied in the package to ensure that the place

for detector attachment is sufficiently even. After the detector has been installed, at

least one of the rear tamper sensors must be permanently closed (pressed).

6. Carefully try out, if the detector (magnet) makes no obstruction when closing the

window/door.

7. If all is in order, you can configure the detector’s functionality (see DIP switches

below).

8. Enter enrollment mode on the control panel (or on a receiver). Subsequently,

install battery cells into the detector and screw the battery cover on (2 screws).

After connecting the battery the detector will send an enrollment signal. Up to 10

seconds’ delay is to be expected to the detector’s response to putting the

magnet away/close or pressing/releasing tamper sensors.

9. After the detector has been enrolled, you can check its functioning. On the Oasis

control panel, you should also check signal strength.

DIP switches

There are four DIP switches located under the battery cover:

No.

OFF ON

1 Rear tamper sensors OFF

Rear tamper sensors ON*

Permanent window/door status

signalling

Only window/door opening will be

signalled **

3***

The system will provide an exit

/ entrance delay

The system will respond with an

instant alarm

No function

Default settings are shown in bold

* To detect intrusion the switch should be ON.

** Switching ON (when only window/door opening will be signalled) is suitable for

bedrooms, where windows/doors are left open for ventilation during the

protection period.

*** This setting will apply if the detector is used with an Oasis control panel with a

natural reaction pre-programmed for the detector’s address.

Detector functionality

If DIP switch no. 2 is OFF, the detector will indicate whether the window/door is

open. When used within an Oasis system and the system is set (armed) while

the window/door is open, the detector will be bypassed. However, if somebody

closes the window/door while the system is set, then subsequently opening it

will trigger an alarm. This also applies to pulling the window/door handle by

string. If you do not wish permanent window/door open status to be indicated

on the keypad, then DIP switch no. 2 should be ON. This will ensure that only

window/door opening will be signalled.

Battery replacement

The detector monitors its battery voltage and if too low, a report is sent to the

control panel to inform the installer or user. The detector continues to function,

however battery replacement should not be delayed by more than two weeks.

Always replace both battery cells. We recommend using a high quality brand-

name battery (e.g. Panasonic). After the battery has been replaced, detector

functioning should be tested.

Expired batteries should not be thrown into the garbage, but disposed of

according to local regulations.

Removing the detector from the system

If a detector is removed, the control panel announces the removal. The

detector has to be deleted in the control panel before intentional removal.

Technical specifications

Voltage Lithium battery type CR2354 - 2 pc (3.0 V, 1 Ah), power source type C

Typical battery lifetime approx. 3 years (for 5 daily activations maximum)

Communication band 868 MHz, Oasis protocol

Communication range approx. 200m (open area)

Dimensions 192 x 25 x 9 mm

Operational environment EN 50131-1 class II. internal

Operational temperature range -10 to +40 °C

Classification: grade 2

according to: EN 50131-1, EN 50131-2-6, EN 50131-5-3

Complies with: ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1

Can be operated according to: ERC REC 70-03

FCC ID VL6JA82M

JABLOTRON ALARMS a.s. hereby declares that the JA-82M is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC and

complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: 1. This device may not cause harmful interference, and 2. This device must

accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could void

the user´s authority to operate the equipment.

The original of the conformity

assessment can be found at www.jablotron.com

, Technical Support section

Note: Although this product does not contain any harmful materials we suggest you

return the product to the dealer or directly to the producer after use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82M in the language / languages: English as an attachment in your email.

The manual is 0,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-82M Manual

Product: