Output, copies the state of the EW output of the enrolled
control panel
IW
Output, copies the state of the IW output of the enrolled
control panel
PGX
Output, copies the state of the PGX output of the enrolled
control panel
PGY
Output, copies the state of the PGY output of the enrolled
control panel
GND
Negative pole of the wired detector’s and the temporary
beeper’s power supply
B
Possitive pole of the temporary beeper (negative is
connected to the GND)
+U
Positive pole of the wired detector’s power supply (protected
by FU1 – F1A)
DIP switch description
DIP1
The input on the INP terminal is switched on (monitored) in
“ON” position
DIP2
The rear tamper sensor is active in the “ON” position
DIP3
No function
DIP4
The enrollment mode is active in the “ON” position
Device reset
Resetting the whole device is irreversible and causes the deletion of the
enrolled control panel and all enrolled devices from the repeater.
1. Switch off the 230V power output and disconnect the backup battery.
2. Connect the RESET jumper and leave it connected.
3. Connect the supply voltage and the battery.
4. Disconnect the RESET jumper.
Technical specifications
Power source 230 V / 50 Hz, max 0.1 A, protection class II
Power supply type A (EN 50131-6)
Backup battery 12 V, 2.2 Ah
Backup power output maximum continuous load 0.7 A
Number of wireless device addresses 40
Hard-wired inputs 1x double balanced input
1x input reserved for the rear tamper contact
EW external warning output switching to GND, max. 0.5A
IW internal warning output switching to GND, max. 0.5A
PGX, PGY outputs max. 0.1 A, switching to GND
Frequency (JA-82R) 868 MHz
Security grade 2
according to EN50131-1, EN 50131-6 and EN 50131-5-3
Environmental class II. indoor-general (-10 to +40°C)
compliant with EN 50131-1
Radio emissions ETSI EN 300220
EMC EN 50130-4, EN 55022
Safety EN 60950-1
Can be operated according to ERC REC 70-03
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-80Z at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-80Z in the language / languages: English as an attachment in your email.
The manual is 0,02 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.