Manual Jablotron JA-80V - LAN Communicator (page 9 of 10) (English)

631259

Zoom out

Zoom in

1/10

The JA-80V LAN/PSTN line communicator - 9 - MKA51202

5.28. ARC communication checking period

The time to wait after the last report sent to an ARC before performing

an ARC communication check is set by this sequence. The

communication-checking event code is 31 (see 5.26). This sequence

programs how often the communication check is performed:

07 a hhmm

where

a 1 = ARC1, 2 = ARC2

hh hours

mm minutes

Notes:

• Checking reports are not sent in service mode

• IP CID protocol allows very frequent checking of ARC

communication (e.g. every 5 minutes).

Factory default setting: 24 hours after the last report – for both ARCs

5.29. Enable ARC reporting (ARC2 backs up ARC1)

This sequence allows reporting to ARCs to be switched on/off and also

enables ARC2 to backup ARC1:

00 a x

where

a 1=ARC1, 2=ARC2

x 0=off, 1=on, 2= ARC2 backs up ARC1 (2 can only be

entered for ARC2)

Note: if ARC2 backs up ARC1 then it will only receive data if it is not

possible to deliver it to ARC1. A report containing “Communication

fault to ARC1” is then sent to ARC2 together with the first report to

ARC2.

Factory default setting: both ARCs = off

5.30. Recording reports sent to ARCs in the control panel

memory

This sequence enables the recording of every report successfully

communicated to ARCs in the control panel’s internal memory.

080 enabled

081 disabled

Note: it is recommended not to record reports sent to ARCs but to

enable the indication of ARC communication faults (see 5.31). This

saves a significant amount of control panel memory. The system

initially assumes that every report is successfully delivered to ARCs,

but if a report is not successfully delivered within 110 seconds of

transmission, then a communication fault will be indicated and

recorded.

Factory default setting: enabled

5.31. Indicate an ARC communication fault if a report is not

successfully received within 110 sec of transmission

Enables the indication and recording of a communication fault if a

report is not successfully delivered to an ARC within 110 seconds of its

transmission.

090 communication faults not indicated

091 communication faults indicated

Notes:

• The communicator continues trying to send information to an ARC

even after a communication fault has been indicated (after the data

has been delivered, communication fault indication stops).

• For communication-checking reports the delivery time limit

(confirmation from the ARC) is 300 minutes. But if any other report is

sent to the ARC it must be confirmed within 110 seconds (otherwise

a communication fault will be indicated)

Factory default setting: communication faults not indicated

5.32. IP address for data transmission

The communicator supports transmission of the special data (e.g.

visual information for the img.jablotron.com ) from the system to set IP

address, which can be set by following sequence:

013 xx..x ∗0 where:

xxx...x is IP address and port – set in format as shown in the

example:

01 3 ∗8 192 168 021 123 08080 ∗0

∗8 insert # character, to identify the IP address which must

consist of 12 digits followed by 5 digits of the port

To erase the IP set 013∗0.

Factory default : IP address is set to 77.104.220.129 7070

(img.jablotron.com)

5.33. Locking the ARC settings

All settings which effect reporting to ARCs can be locked by a digital

code:

901 xx..x ∗0 where xx..x is an installer-defined locking code (4 to

8 digits)

Notes:

• Exiting service mode after the locking code has been entered will

lock all the settings effecting ARC communication (see the

sequence list in section 5).

• If ARC programming is locked, then it can be temporarily enabled

in service mode by entering 900 xx..x ∗0 where xx..x is the locking

code. It will then relock on exiting service mode.

• The ARC settings can be permanently unlocked by entering 901∗0

while ARC programming is temporally enabled – see above. This

will erase the locking code.

Factory default setting: ARC settings unlocked

5.34. Engineer reset

The Engineer reset also requires the control panel firmware to be of

version KE60108 or higher. This feature is designed for ARC (Alarm

Receiving Centre) connection to satisfy the following requirements of

the DD243 standard: After a confirmed alarm has been triggered, the

control panel must switch to a disabled state. Switching to normal

operation is then only possible using a valid ARC access code. Until

then, the system remains completely disabled – no operation or

programming is possible even when in Maintenance or Service

mode.

An ARC access code can be entered:

GSMlink in the field used for remote code entry

SMS instruction

ARC-code_instruction

(e.g.

12345678 STATUS)

6. LAN network configuration

Each device in an Ethernet network (LAN, internet) has its own IP address

(e.g. 192.168.250.20). This address can either be a public or private one.

Before connecting the LAN network cable, setting up the LAN network

should be done – either by automatic DHCP or manually (see 5.18).

 If automatic DHCP is used, contact your network supervisor and ask

him to make the network ready for the communicator. If he needs the

communicator MAC address you will find it on the label attached to the

communicator board.

 Manual programming of the network parameters should be done by a

network supervisor who knows how to program these parameters.

7. Further guidance on the communicator

7.1. How the communicator sends reports

If there is a need to report an event (e.g. an alarm) then the

communicator:

• sends data to ARC1, if used (the communicator tries the main IP

address, if unsuccessful then it tries the backup IP address).

• Then it sends data to ARC2 in the same way if programmed as an

independent ARC. If ARC2 is programmed as the backup to ARC1

then the data will only be sent to it if transfer to ARC1 has been

unsuccessful.

• Then the unit sends SMS reports (1

tel. number, 2

tel. number ….8

tel. number)

• Then the unit performs reporting by phone call (1

tel. number, 2

tel.

number ….8

tel. number) – each programmed number is called once

whether the call has been answered or not

• If all previous attempts to send data to ARCs have been unsuccessful,

the next attempts occur after the programmed repeat period (see

5.27).

If an alarm is cancelled by a user while it is being reported, any unsent

SMSes and unperformed call reports are cancelled, but the ARC still

gets a complete set of reports about events in the system.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80V - LAN Communicator in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80V - LAN Communicator Manual

Product: