Alternatively it can be connected to an AS-80 unit
as a part of a stand-alone access system.
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by technicians
holding a certificate issued by an authorized
distributor. It is usually placed near an entrance door
(equipped with an electronic lock). The reader can be
used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the reader cable to pass
through, where the reader will be located.
3. Attach the rear cover to the desired location (the
tamper spring must be properly pressed)
4. Pull the reader cable through the wall hole and to the
interface unit’s box (WJ-80, AS-80)
5. Attach the reader to the rear cover and secure it using
the screw
6. Connecting and setting up the reader is described in
the WJ-80 or AS-80 manuals.
Cabling
wire signal
red +12V(power supply, 60mA)
greenD0(Wiegand 26b data output)
brown D1(Wiegand 26b data output)
whiteTMP (normally closed tamper contact)
grey TMP (normally closed tamper contact)
yellow BZR(input controlling reader’s sound – connecting to GND
generates a beep on the reader)
blueGND (common ground)
pink not connected
Configuring the reader for operation with the WJ-80
If the JA-80N reader is connected to an Oasis control panel and it does
not work as described in the manual, then it is not set to the correct
(factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Get an RFID card ready (PC-01 or PC-02)
4. Disconnect the yellow and brown wires from the WJ-80 interface
terminals and connect the wires together
5. Power-up the control panel (reader starts beeping)
6. Disconnect the yellow and brown wires from each other (beeping will
terminate)
7. Use the RFID card 4 times (put it close to the reader and after a short beep
take it away) – then wait a moment until a few beeps sound (by this
procedure you enter “4” without pressing a key, as there are no keys to
press)
8. Now use the RFID card 3 times (put it close to the reader and after a short
beep take it away) – then wait a moment until a few beeps sound (by this
procedure you enter “3” without pressing a key, as there are no keys to
press)
9. Disconnect the power from the control panel, connect the yellow and brown
wires back up, power-up the control panel and check the proper functioning
of the JA-80H keypad
Note: The red LED is lit in normal operating mode. Using a card is confirmed
by a flash from the orange LED.
How to set up the
JA-80N reader for the AS-80 access system is described in
the AS-80 manual.
Technical specifications
Power supply 10 to 16V DC
Stand-by consumption typically 60mA
Enclosure protection (EN 60529) IP65
Mechanical endurance (EN 50102) IK08
Environmental (EN 50131-1) class IV – outdoor general
Operational temperature range -25 to +60°C
RFID card Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions 46 x 150.5 x 22.5mm
Length of the connection cable 1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Can be operated according to ERC REC 70-03
FCC ID VL6JA80N
Jablotron Ltd. hereby declares that the JA-80Nis in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC and complies
with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.
This device may not cause harmful interference, and 2. This device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the
user´s authority to operate the equipment.The original of the conformity assessment can
be found at www.jablotron.com
, Technical Support section.
Note: Although this product does not contain any harmful materials
we suggest you return the product to the dealer or directly to the
producer after use.
TAMPER
22,545
151,5
87,5
cca 1 m
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-80N at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-80N in the language / languages: English as an attachment in your email.
The manual is 0,05 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
