The JA-80H outdoor keypad and RFID card reader MKM51101
1
The JA-80H outdoor keypad and RFID card reader
The JA-80H is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and
connects to the Oasis control panel via a WJ-80
interface.
Alternatively it can be connected to an AS-80 unit
as a part of a stand-alone access system.
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by
technicians holding a certificate issued by an
authorized distributor. It is usually placed near an
entrance door (equipped with an electric lock). The
keypad can be used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the keypad cable to
pass through, where the keypad will be located.
3. Attach the rear cover to the desired location (the
tamper spring must be properly pressed)
4. Pull the keypad cable through the wall hole and to the
interface unit’s box (WJ-80, AS-80)
5. Attach the keypad to the rear cover and secure it
using the screw
6. Connecting and setting up the keypad is described in
the WJ-80 or AS-80 manuals.
Cabling
wire signal
red +12V(power supply, 60mA)
greenD0(Wiegand 26b data output)
brown D1(Wiegand 26b data output)
white TMP (normally closed tamper contact)
grey TMP (normally closed tamper contact)
yellow BZR(input controlling keypad sound – connecting to GND
generates a beep on the keypad)
blueGND (common ground)
pink not connected
Configuring the keypad for operation with the WJ-80
If the JA-80H keypad is connected to an Oasis control panel via a WJ-80
and it does not work as described in the manual, then it is not set to the
correct (factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Disconnect the yellow and brown keypad wires from the terminals
and connect them together.
4. Power-up the control panel (keypad starts beeping)
5. Disconnect the yellow and brown wires (beeping will terminate)
6. On the JA-80H keypad, press button 4 (beeps once) and then button 3
(beeps several times)
7. Disconnect the power from the control panel, connect the yellow and brown
wires back up, power-up the control panel and check the proper functioning
of the JA-80H keypad
Technical specifications
Power supply 10 to 16V
Stand-by consumption typically 60mA
Housing IP65 (EN 60529)
Mechanical resistance IK08 (EN 50102)
Working environment class IV(EN 50131-1)
Operational temperature -25 to +60°C
RFID card Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions 46 x 150.5 x 22.5mm
Length of the connection cable 1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Can be operated according to ERC REC 70-03
FCC ID VL6JA80H
Jablotron Ltd. hereby declares that the JA-80His in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC and complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron
could void the user´s authority to operate the equipment.The original of the
conformity assessment can be found at www.jablotron.com, Technical
Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
TAMPER
22,545
151,5
87,5
cca 1 m
Note: The red LED is lit in Oasis normal operating mode. Pressing a button
is confirmed by a flash from the orange LED.
How to set up the JA-80H keypad for the AS-80 access system is described in the AS-80 manual.
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-80H at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-80H in the language / languages: English as an attachment in your email.
The manual is 0,06 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
