The JA-80A is a component of Jablotron’s Oasis 80 system. It is
designed to sound an external alarm and to indicate any tampering it
experiences. It is powered by a long-life lithium battery and
communicates wireless using Jablotron Oasis protocol.
BAT - 80
100
158
1
6
0
2
3
0
Installation
The siren should be installed by a certified installer. It should be
located on a vertical wall with its flashing light facing downwards. The
siren should not be shielded by any metal which could block radio
communication.
1. Open the siren cover (2 screws on the bottom side)
2. Attach the siren to the desired location (3 screws)
3. Select the desired optional features via the internal jumpers
(see the following description)
4. Enroll the siren to the control panel as follows:
a) Set the control panel to Service mode and key in 1 to enter
enrollment mode (the desired address can be selected by
using the arrow keys)
b) Connect up the battery cable in the siren – (the light will
flash and after a while it will turn off = enrollment finished)
c) Exit enrollment mode by pressing the # key
5. Reinstall the external cover
Notes:
• Multiple sirens can be enrolled to the control panel
• If the siren continues flashing it has not been enrolled –
check if the control panel is in enrollment mode and if it has
its antenna connected. The siren should be at least 2 meters
away from the control panel during enrollment.
Jumpers
50 / 25 selects how often the siren checks the status of the system. In
normal operation the siren saves battery power by turning its receiver
off. It then turns on again periodically to check for alarms in the system
every 25 or 50 seconds (selectable). The 50 second period not only
extends the siren’s maximum reaction delay but also its battery life.
LED ON / OFF enables short flashes of the siren every 60 seconds (=
position ON).If OFF is selected, the siren will flash only while
indicating an alarm.
Siren connector
(beware of high voltages)
LEDs
Top cover sensor
Siren removal sensor
Battery connector
enabled
disabled
communication
interval 25s
interval 50s
LED indication
antenna
Function
If there is an external alarm in the control panel, the siren will start
sounding and flashing (can be delayed – see the 50/25 jumper). The siren
will sound for a maximum of 3 minutes (unless the control panel alarm
period is shorter) and its light will flash 30 minutes longer. Siren indication
can also be stopped by ending the alarm in the control panel.
If tampered with, the siren will send a tamper signal to the system
Warning – beware of electrical shocks when the siren sounds (it
generates a high AC voltage – do not touch any internal parts). Switch
the system to Service mode before performing any maintenance on
the siren. Remember, that the siren can start sounding and flashing
anytime when its battery is connected.
Testing
If you trigger an external alarm in the system, the siren should start
working within 25 (or 50) seconds.
To measure the siren’s signal strength select signal measurement
mode in the control panel and activate the siren tamper sensor by
opening its cover.
Battery replacement
The siren checks its battery status and if it is going to be discharged soon it
will inform the system (which will notify the user and service technician).
The siren will continue to work, but its battery should be replaced within 2
weeks. Only use a Jablotron BAT-80 battery as a replacement.
Never try to charge the battery. When disposing of the used battery
always follow local regulations.
Removing the siren from the system
If you want to uninstall the siren, do not forget to erase it in the control
panel to avoid any indication of lost communication with the siren.
Specifications
power lithium battery BAT-80 Jablotron 6 V, 11 Ah
battery life time calculated for max 3 years (50 sec supervision)
communication band 868 MHz, Oasis protocol
communicating distance up to 300m (open area)
siren piezo electric, 112 dB/1m
max. duration of the audible alarm 3 minutes
max. duration of flashing during alarms 30 minutes
enclosure (EN 60529) IP34D
EN 50131-1, EN 50131-4, EN 501321-5-3 grade 2
working temperature -25 to +60°C
operating environment class IV.
dimensions, weight 230 x 158 x 75 mm, 850 g
Complies with ETSI EN 300220, EN 50130-4, EN 55022, and EN 60950-1
can be operated according to ERC REC 70-03
JABLOTRON ALARMS hereby declares that the JA-80Ais in compliance
with the essential requirements The original of the conformity assessment
can be found at www.jablotron.com
, Technical Support section
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer after
use.
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-80A at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-80A in the language / languages: English as an attachment in your email.
The manual is 0,09 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
