554999

Jablotron JA-60SP Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
JA-60SP Wireless Optical Smoke Detector
The JA-60SP detects smoke or temperature overrunning and wirelessly
transmits this information to a receiving unit (control panel). It also has a
built in siren to warn people in the immediate vicinity. For testing purposes
the detector is equipped with a testing button. You can also test it remotely
using any audio/video IR remote control (TV, stereo etc.).
The detector makes regular auto testing and reports its condition
to the system regularly for full supervision.
JA-60SP Wireless smoke detector 2 / 2 MGV51007
Specifications
Power 3 V - 2 x AA battery 1.5V
Battery lifetime about 1 year
Consumption Stand-by 40
µ
A
Wireless communication range max. 100 m (open area)
Detection method IR light detection
Detection temperature 60 °C to 70 °C (depending on speed of
temperature rising)
Sensitivity m = 0,05
÷
0,07 at 1m/s (EN 54-7)
Built in siren 95dB/1m
RF immunity 30V / 1m
Working environment indoor use , IP-40
Working temperature -10 to +55°C
Humidity 25% to 85%
Dimensions
φ
120 x 40 mm
Can be operated according to ERC REC 70-03
Complies with ISO 12239, EN 54-7, ETSI EN 300 220, ETS 300683
Hereby, Jablotron Ltd., declares that this JA-60SP is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Original of the conformity assessment can be found
at the web page www.jablotron.com, section
Technical support.
Contents of the set: detector, 2 plastic dowels, 2 screws, 2 AA batteries
Installation
The detector should be installed on the ceiling, with the distance
from walls 0.6 m as a minimum. The detector should not be installed
in a place with a poor air circulation. If you install the JA60SP in a long
corridor (9 m and more) install at least two detectors one at each end.
The detector can cover an area of about 50 m
3
of free space
(no partitions). The detector should not be installed close to any fan,
heating/cooling vent.
While deciding where to install the detector keep in consideration
that detector’s batteries have to be replaced from time to time
(approximately once a year).
Note: the detector can also be triggered by heavy cigarette smoke
and smoke generated during cooking.
• Open the cover of the detector (press it from both sides up to the
lines on the housing – see the picture)
• Attach the rear panel with the two provided screws to the desired
location. Tighten the screws firmly being sure that the panel is not
crooked.
• Study the installation manual of the receiver unit (control panel)
to learn how to enter the enrolling mode to enroll the detector.
• Connect batteries in the detector (remove the plastic tape). The
JA-60SP will transmit an enrollment signal and its buzzer will make
a short beep. From this moment the detector is ready to work.
• Attach the detector’s front cover to the rear panel so that both tabs
click. Check that the detector is fixed firmly.
• Press the testing button. The detector will make an alarm sound in
a few seconds and send a testing signal. The testing wireless signal
will be always sent to the INSTANT zone regardless of a
FIRE/INSTANT jumper setting.
Jumpers:
FIRE (default) – if selected, the
detector will make an alarm
sound and the central unit will
be always triggered regardless
of its state (ARM / DISARM).
INSTANT – if selected the built
in siren is switched off. The
central unit will be triggered
only if it is ARMED. This
setting is suitable especially for
some appliance (e.g. fire place) may cause a presence of the smoke.
Warning, in this mode the system
INSTANT/FIRE
IR OFF/ON
location where the common usage of
will not make any fire alarm,
l IR remote control testing can be disabled by
while it is DISARMED!
IR ON / OFF - the interna
this jumper.
Normal operating mode
The detector in normal operating mode performs a self-testing every
ture overrunning is detected, the JA-60SP will
m
tration drops the detector will go to the stand by
m
ting button or use any IR
re
60 seconds (indicated by a short flash of the LED) and reports regularly its
condition to the system.
If smoke or tempera
ake a “soft” warning sound at first and if the smoke concentration does
not go down within 5 seconds, it will trigger an alarm (depending on the
FIRE/INSTANT jumper).
After the smoke concen
ode again. You can stop the internal siren by pressing the test button
or using an IR remote control (see bellow).
To test the detector – press the tes
mote control (if enabled by the IR jumper). Standing under the
detector aim the remote control up to it and press any button. Note that
different remote controls can differ in working distance. The detector will
generate soft beeps at first and within a few seconds it will start an alarm
(built in siren & signal to the alarm system). The testing signal will be
always sent to the INSTANT zone regardless of FIRE/INSTANT
jumper setting.
Battery replacement
The detector checks the batteries automatically. If it is necessary to
re
ity alkaline AA batteries for replacement. After
in
r the batteries are installed and the LED is
fla
ries!
yo
of the
ba
place them the detector will inform the system and it will start to generate
“soft” beeps every minute.
Use only new high qual
stallation of new batteries the detector’s buzzer will make a sound
to confirm that it is ready.
If there is no sound afte
shing, it means that the installed batteries have a low voltage.
Warning it is impossible to close the detector without batte
: we recommend removing dust from the detector every time Note
u replace the batteries. Use a dry cloth or blow on it gently.
Note: Dispose of batteries safely depending on the type
tteries and local regulation. Although this product does not contain
any harmful materials we suggest you to return the product to the
dealer or directly to the producer after usage.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60SP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60SP in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info