There are several changes and improvements in the new version of the system JA-60 “Comfort”. The reason of the changes is to
extend the current system and some of them are the result of communication with customers and installation companies.
The bellowed list pertains to the SW version FM 61211 compared to the version FM 61210.
Change
Programming
sequence
Function Reason Note
Power supply
check
In case of power failure of the control
panel (battery or mains supply) the
technology alarm is triggered, no matter
what the status of the system is set
(armed/disarmed)
User is warned of the limited function
of the intruder system in any case
Panic
The alarms of the particular sources are
counted up to four, after this number the
detector is ignored if the line of the four
alarm event from this sensor has not
been interrupted by any other source or
by the system status change
(arming/disarming). The panic alarms
are not counted!
The source of the panic alarm, e.g.
panic button, is not ignored after the
fourth alarm event and the sources is
able to transmit any other event.
Delayed
detector test
39X
During the arming process is the user’s
attention drawn to the active delayed or
next delayed detectors
The function was extended for
installation companies demand
Programming
mode
6999
Direct oversetting of the Programming
mode to the User mode without the “N”
key and master code entering
The set bypasses and theirs features
are kept on
Periphery
enrolment
299
The enrolment sequence may be
transmitted in the User mode as well
The user is allowed to enrol
peripheries without the service code
knowledge
Timer 64 nahhmm
Possibility of the counter setting in the
User mode
The user is allowed to set the
automatic arming and disarming
timer without the service code
knowledge
Further
information in
the user manual
JA-60 COMFORT changes overview 2/2 MDY54300
JA-60 “Comfort“ changes overview
There are several changes and improvements in the new version of the system JA-60 “Comfort”. The reason of the changes is to
extend the current system and some of them are the result of communication with customers and installation companies.
The bellowed list pertains to the SW version FM 61211 compared to the version FM 61210.
Change
Programming
sequence
Function Reason Note
Power supply
check
In case of power failure of the control
panel (battery or mains supply) the
technology alarm is triggered, no matter
what the status of the system is set
(armed/disarmed)
User is warned of the limited function
of the intruder system in any case
Panic
The alarms of the particular sources are
counted up to four, after this number the
detector is ignored if the line of the four
alarm event from this sensor has not
been interrupted by any other source or
by the system status change
(arming/disarming). The panic alarms
are not counted!
The source of the panic alarm, e.g.
panic button, is not ignored after the
fourth alarm event and the sources is
able to transmit any other event.
Delayed
detector test
39X
During the arming process is the user’s
attention drawn to the active delayed or
next delayed detectors
The function was extended for
installation companies demand
Programming
mode
6999
Direct oversetting of the Programming
mode to the User mode without the “N”
key and master code entering
The set bypasses and theirs features
are kept on
Periphery
enrolment
299
The enrolment sequence may be
transmitted in the User mode as well
The user is allowed to enrol
peripheries without the service code
knowledge
Timer 64 nahhmm
Possibility of the counter setting in the
User mode
The user is allowed to set the
automatic arming and disarming
timer without the service code
knowledge
Further
information in
the user manual
JA-60 COMFORT changes overview 2/2 MDY54300
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-60 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-60 in the language / languages: English as an attachment in your email.
The manual is 0,01 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.