554982

Jablotron CU-07 Manual

3
Zoom out
Zoom in
Previous page
1/3
Next page
CU-07 Tracer unit 3/3 MKW51102
Command format: Password,REx
where: x – can have the following values:
0 – do not confirm any received SMS commands (default)
1 – confirm with an SMS message sent to the telephone number
from which the SMS command was received
Command example:
123456,RE1 (will be confirmed by
SMS the number from which the SMS command was received)
2.8. Ascertaining the current position
The current position of the unit can be ascertained by sending a
GPS command. The command requires a password. You will
receive an SMS message containing information about the
coordinates in degrees. If your mobile phone supports the direct
browsing of links in the received messages, the SMS also
includes a link to a website where you can directly view a map
showing the given position.
Command format: Password,GPS
Example of a command to ascertain the current position:
123456,GPS
2.9. Enabling SMS sending with activated roaming
The unit can confirm changes (e.g. choice of driver) by sending
an SMS. Confirmatory SMS message sending is forbidden
outside the national network. Enabling this function will result in
increased operating costs of your unit. The command can only
be set through your monitoring service provider.
2.10. Enabling data sending with activated roaming
The unit transmits data concerning the journey in progress to
the server using a GPRS connection. This is forbidden outside
the national GSM network. Enabling this function will result in
increased operating costs of your unit.
The command can only be set through your monitoring
service provider.
Note: If this function is not active, the data is saved in the unit
and it is then transferred to the server when the unit has
registered itself to the national GSM network again. You can
keep more than a month of daily journeys (approx. 15
hours/day) in the memory.
2.11. Notification of vehicle tampering and commencement
of a journey
The unit can notify you when your car is being tampered with
(e.g. shocks, towing away) by calling the telephone number from
which the SMS command was sent. The notification is
functional only if the unit is connected to a permanent
power supply. It becomes active when the journey
termination timeout has finished (see 2.6.) which is
indicated by switching off the LED indicator. You can speed
up the activation of this function by calling the unit’s
number and thus terminating the journey despite the
incomplete timeout.
Another option is a notification about the commencement of a
journey (speed exceeding 3 km/h) by calling the telephone
number from which the SMS command was sent. The
notification is functional only if the unit is connected to a
permanent power supply, and it only becomes active when
the journey termination timeout has finished (see 2.6.)
which is indicated by switching off the LED indicator. You
can speed up the activation of this function by calling the
unit’s number and thus terminating the journey despite the
incomplete timeout.
The above-mentioned “Notification“ functions are not security
functions and they cannot substitute a proper security system.
Command format: Password,Ax
where: x = 1 notification of vehicle tampering
x = 2 journey commencement notification
x = 0 notification disabled *(Note: see the note in
chapter 2.11. “Default settings“)
Command example:
123456,A1 (the unit calls the telephone
number from which the SMS command was send for approx. 15
seconds)
2.12. Default settings
Default settings of the unit’s settable parameters:
TELx the drivers’ telephone number list is empty
T journey type 00 (business)
D driver ID 01
ET journey time-out 300 s. (5 min.)
A dialling in (calling) 0 (disabled)
RE SMS confirmation 0 (disabled)
MC password set as 123456
* Note: when setting an SMS command concerning
confirmation by calling back (see 2.7.), it is necessary to
deactivate “voice mail“. Voice mail accepts calls
automatically even after the user’s call rejection which
results in increased operating costs for the unit's SIM card !
3. Technical specification
Power supply voltage ═ 8 - 30 V
Maximum power consumption 200 mA /12 V
Nominal current in GPRS mode 120 mA /12 V
Standby consumption 15 mA /12 V
Dimensions 160 x 42 x 19 mm,
Weight 84 g
Operating temperature range -20 to +80°C
Comply with ETSI EN 301 511, ETSI EN 301 489-1,
EN 60950-1
Intended for connection to a 12V or 24V power supply. The unit
is intended for operation in road vehicles.
JABLOTRON ALARMS a.s. hereby declares that the CU-07 is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and ECE Regulation No.
10.03. The original of the conformity assessment can be found
at www.jablotron.com
, Technical Support section .
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
10R-03 5144
E
8
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CU-07 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CU-07 in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info