554988

Jablotron CA-550 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
The CA-550 tilt detector 2/2 MGX51010
The CA-550 tilt detector installation, operation manual
The CA-550 tilt detector detects movement of the car in two
axes (x and y). No mechanical parts are used in the detector.
Detection is achieved through electronic acceleration metering.
The digital analysis used in this detector ensures high
resistance against the false alarms. When the alarm is armed
(power supply connected) the reference position of the detector
is stored in the memory after which the position of the detector is
continuously checked, compared and updated. If the tilt of the
car is changed by more than 1
°, the detector will be triggered.
Specification:
Power 9 - 16V (DC)
Power consumption typ.1 mA
Operating temperature -40 °C to +85 °C
Maximum sensitivity (for both axes) 1° (built-in digital filter)
Angle of operation with max. sensitivity preservation ± 45° from reference (horizontal) position
Installation position of the detector ± 15° from horizontal (both axes)
Output negative pulse with a duration of 0.5 s
Maximal output load 80 mA
The CA-550 complies with the essential requirements of: 95/56/EC Directive relating to devices
to prevent the unauthorized use of motor vehicles and
89/336/EC EMC Directive - Protection
concerning electromagnetic compatibility when is used for its intended purpose
Wiring:
Red Power supply + 12V. It can be connected either permanently to +12V, or to the switching
output of the alarm (where +12V is present when the alarm is armed).
Black GND – connect to the original grounding of the car.
White Output - if the detector is triggered the output will be connected to GND for 0.5 sec. It is
short-circuit protected. The output should be connected to the external detector input of
the car alarm.
Installation:
The CA-550 tilt detector should be installed on the floor in the interior of the car where there is no danger
of mechanical damage or high humidity (the lowest part of the floor). Fix it using a double sided Velcro
sticker or by screws. The detector must be installed in a horizontal position with a maximal deviation of ± 15°
in both axis (x and y). If the detector is fixed by a screw, only one bigger hole in the middle of the detector
should be used. The smaller holes in the corners of the detector are not designed for this purpose. The
screw should be tightened carefully so as not to damage the housing of the detector.
Function:
When the alarm is armed (power supply connected) the reference position of the detector will be stored in the
memory (max 30 seconds). The position of the detector is continuously checked, compared and updated. If the
tilt changes by more then 1
°, the output will be switched to ground for 0.5 sec. Default parameters are re-set
after detector activation. It can take up to 30 seconds (depends on the amount of detected tilt). If the maximum
output load of 80 mA is exceeded, the electronic fuse will temporarily switch off the output. A built-in digital filter
ensures that the detector will not be triggered by a short tilt of the car, caused, for example, by sudden burst of
wind after which the car will return to its original position.
Maintenance
The device does not require any special maintenance. To check correct functioning, we recommend
triggering an intentional alarm from time to time.
Note: Although this product does not contain any harmful materials we suggest you to
return the product to the dealer or directly to the producer after usage.
The CA-550 tilt detector 2/2 MGX51010
The CA-550 tilt detector installation, operation manual
The CA-550 tilt detector detects movement of the car in two
axes (x and y). No mechanical parts are used in the detector.
Detection is achieved through electronic acceleration metering.
The digital analysis used in this detector ensures high
resistance against the false alarms. When the alarm is armed
(power supply connected) the reference position of the detector
is stored in the memory after which the position of the detector is
continuously checked, compared and updated. If the tilt of the
car is changed by more than 1
°, the detector will be triggered.
Specification:
Power 9 - 16V (DC)
Power consumption typ.1 mA
Operating temperature -40 °C to +85 °C
Maximum sensitivity (for both axes) 1° (built-in digital filter)
Angle of operation with max. sensitivity preservation ± 45° from reference (horizontal) position
Installation position of the detector ± 15° from horizontal (both axes)
Output negative pulse with a duration of 0.5 s
Maximal output load 80 mA
The CA-550 complies with the essential requirements of: 95/56/EC Directive relating to devices
to prevent the unauthorized use of motor vehicles and
89/336/EC EMC Directive - Protection
concerning electromagnetic compatibility when is used for its intended purpose
Wiring:
Red Power supply + 12V. It can be connected either permanently to +12V, or to the switching
output of the alarm (where +12V is present when the alarm is armed).
Black GND – connect to the original grounding of the car.
White Output - if the detector is triggered the output will be connected to GND for 0.5 sec. It is
short-circuit protected. The output should be connected to the external detector input of
the car alarm.
Installation:
The CA-550 tilt detector should be installed on the floor in the interior of the car where there is no danger
of mechanical damage or high humidity (the lowest part of the floor). Fix it using a double sided Velcro
sticker or by screws. The detector must be installed in a horizontal position with a maximal deviation of ± 15°
in both axis (x and y). If the detector is fixed by a screw, only one bigger hole in the middle of the detector
should be used. The smaller holes in the corners of the detector are not designed for this purpose. The
screw should be tightened carefully so as not to damage the housing of the detector.
Function:
When the alarm is armed (power supply connected) the reference position of the detector will be stored in the
memory (max 30 seconds). The position of the detector is continuously checked, compared and updated. If the
tilt changes by more then 1
°, the output will be switched to ground for 0.5 sec. Default parameters are re-set
after detector activation. It can take up to 30 seconds (depends on the amount of detected tilt). If the maximum
output load of 80 mA is exceeded, the electronic fuse will temporarily switch off the output. A built-in digital filter
ensures that the detector will not be triggered by a short tilt of the car, caused, for example, by sudden burst of
wind after which the car will return to its original position.
Maintenance
The device does not require any special maintenance. To check correct functioning, we recommend
triggering an intentional alarm from time to time.
Note: Although this product does not contain any harmful materials we suggest you to
return the product to the dealer or directly to the producer after usage.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-550 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info