555049

Jablotron CA-322 Accent Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Immobilizer CA-322 „Accent“ 2 / 2 MDF532 05
antenna
+12V
ignition
key (15)
turn
indicators
remote control
(max. 3x)
battery
12V
3x immobilization contacts
(3x max. 15 A)
1
1
2
6
7
4
5
8
1413
1314
dome
light
door switches
trunk switch
central
locking
LED indicator
push button
VALET
LR
CA-322
main unit
132
2
4
456
unlock
lock
el. powered
windows
AL1 input
8
Immobilizer CA-322 „Accent“ - operating instructions
Arming
After switching off the ignition, removing your key and exiting the
vehicle, close all the doors (closing of all windows is also
recommended). ARM the immobilizer by pressing the button (A or
B) on the remote control.
One flash from the turn lights confirms arming and the LED
starts to flash. At the same time the immobilizer is blocked and the
doors should automatically lock (if equipped with central-door
locks). If a powered window control system is also connected to the
„lock“ signal, all the windows will be closed automatically* when button A is
used for arming (button B arming does not have any influence on the
windows).
Disarming
To disarm the immobilizer press a button (either A or B) on the remote control
once.
The turn lights should flash twice. At the same time the doors should unlock
(if equipped with central-door locks) and the LED should turn off. When you
open a door the dome light will come on for 60 seconds or until you switch on
ignition key.
REARM* - if you do not enter the car within one minute after disarming, the
immobilizer will rearm and lock the doors automatically again.
AUTOIMMO* will block the car automatically if the ignition key is turned off for
more than 5 minutes. This immobilization (doors stay unlocked) is indicated by
intermittent LED light. The immobilization can be switched off by a remote control
button (A or B). It will also switch off if you switch on the ignition key and press
the VALET button /*. Automatic immobilization can also be temporarily disabled
if you switch off the ignition key while the VALET button is pressed. The
AUTOIMMO function will be disabled until the remote control is activated
again. This can be used, for example, when you leave your car in a car shop
for maintenance without the remote control.
Emergency Disarming*
If you lost your remote control, perform following: Open the car door, switch on
the ignition key and press the hidden VALET switch.
Note: If emergency disarming was disabled in setting mode, there is no way to
disarm the immobilizer (call service).
No reaction of Immobilizer to remote control
If there was any attempt to scan the remote control code (or while rare, as
may happen after the remote control battery has been replaced) then the
immobilizer will not respond to the signal from the remote control. In this case
the system asks you for a confirmation of control code validity.
To provide, make Emergency Disarming (if armed), switch on the ignition
key and press the button of the remote control (A or B). After that the remote
control should work as usual (if not, go to service).
Note: this way your system performs more complicated analyses of coding
system. It insures your immobilizer is secure from outside interference and the
remote control is indeed yours.
Maintenance
There is no special maintenance required. If the distance from your car at
which the system can be operated continuously decreases, then replace the
remote control battery (after releasing of a screw on the rear side of remote
control housing; mind the battery polarity). A suitable replacement battery is
L1016 (6VDC). Usual good battery life time is one year.
We recommend a yearly professional inspection of the immobilizer. Periodic
inspections should be made to the door switches.
We recommend installer to give a detail explanation of „Accent“ functions
to the customer after installation, to avoid problems and misunderstandings in
future.
* these functions are selectable in setting mode
Examples of „Accent“ use for different central locking systems
If your locking system needs another kind of control signal than negative
pulses, install a couple of over-switching relays to the Accent outputs (or you can
use CR-2 relay unit). See following diagrams for different locking systems.
System with positive control inputs:
Pneumatic central locking system:
Program duration of output pulses 2 or 4 seconds according to the reaction
time of the pneumatic system.
Simplified additional installation of central locking system:
When
manual operation of the whole system from the driver's door is not requested,
you can use the following easy solution. Install two-wires actuator (recommended
type CM-2) to each door of your car. Connect them as shown in the following
diagram. Program duration of Accent output pulses 0.3 seconds. This way all
actuators are operated with the remote control.
When necessary, the door locks can also be operated manually with a key
(the same way as before the central locking installation).
Caution : In this case do not use longer locking signal !
Internet: www.jablotron.cz
Tel.: +420 483 559 999
fax: +420 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-322 Accent at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-322 Accent in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info