555037

Jablotron CA-1803BT - reset 1 Manual

5
Zoom out
Zoom in
Previous page
1/6
Next page
GSM car alarm CA-1803BT „Athos“ 5/6 MHF56603
17 SET 64 Car alarm reports
18 AUXA 65 Status:
19 AUXB 66 Armed
20 GPS 67 Disarmed
21 TIME 68 Ignition key ON
25 ON 69 Ignition key OFF
26 OFF 70 Engine is blocked
Events: 71 Engine is unblocked
30 Alarm 72 No alarm
31 Alarm cancelled by a user 73 Alarm timeout
32 Fire alarm 74 Low battery voltage
33 Tamper alarm 75 Power failure
34 Disarming 76 Power recovery
35 Arming 77 Time
36 Low battery voltage 78 Low back-up battery voltage
37 Engine is blocked 79 Partially
38 Engine is unblocked 80 Location
Source:
Confirmation SMS:
40 Ignition key 81 Command accepted
41 Door contact 82 Command syntax error
42 INP1 activation 83 New MC code:
43 INP2 activation 84 New UC code:
44 Low battery voltage sensor 85 Reset
45 Telephone 1 86 Registered phone number:
46 Telephone 2 87 Credit:
47 Telephone 3 88 LEARN mode, enrolled
Use only ASCII character set during the text edition.
10. Functions related to GPS
An integrated GPS (Global Position System) allows the car alarm to
provide information about car location with a high precision. The
location can be obtained upon an SMS request or via the GSMLink
internet web page. A service for regularly sent location information is
also available. The car alarm is capable of recording all the car’s
locations into internal memory while the car is being used (optional).
Records can be used for statistics about car use (route listing etc.).
The information is also partially available via the GSMLink internet
page. Fully-fledged use is possible using a special service only. In that
case, a central monitoring station is required with information being
automatically downloaded. For more information, consult the
manufacturer or visit the http://www.jablotron.com
web page.
10.1. Location detection using GPS
Using a GPS instruction, you can instantly detect the car’s location.
The car alarm responds with the coordinates of the latest known
location. If the current location is not available at the time of reception
of the instruction, or if the car alarm does not change it global position
for a while, the latest location stored in internal memory is sent.
Therefore, messages are supplemented with GMT (Greenwich Mean
Time). The value corresponds to the time of detection related to the
prime meridian. In addition, information about altitude, velocity and
local time of the GSM network is provided. Information about location
can be sent automatically after an alarm has been triggered (see the
DIP switches description).
An example of an instruction sent from an authorized phone: GPS
An example of response: Car alarm reports: Location:
(GMT:3.12.10:35) 50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35
(GMT:3.12.10:35) Greenwich Mean Time (mean meridian)
50*43.495N;15*11.253E latitude and longitude
515 altitude (approximated)
50 current velocity
Time:3.12.05 11:35 current local time
10.2. Time zone setting
To adjust the time information to local time, time zone setting is
possible. The car alarm adds/subtracts the time shift, expressed in
hours, to the GMT time (for middle Europe: +2 hours in summer time,
+1 hour in winter time). This instruction is only available with the
MASTER code.
Instruction: MASTER TIME ±xy
xy is the time shift in hours -3,-2 …+1,+2 relative to GMT
MASTER TIME GSM
turns on automatic setting via incoming SMS.
10.3. Location change in the armed state
The car alarm allows you to supervise changes in the location of the
car in the armed state. See the corresponding SET parameter.
If switched ON, every change of car location detected during the
armed state triggers an alarm. Because the GPS receiver could be in
stand-by mode (due to energy saving) the car alarm could react with a
delay of up to 10 minutes. This function depends on the accuracy of
location determination; therefore only use this function as information,
not as a security function.
10.4. Integrated Bluetooth module (BT)
A Bluetooth module is supplied as a built-in part of the CA-1803BT
car alarm. The module allows the car alarm to communicate with
nearby devices equipped with Bluetooth connectivity. For devices like
PDAs, MBAs or mobile phones, such communication can make use of
navigation software running on these devices. When disarmed and
with the ignition key on, the car alarm sends GPS coordinates via the
BT which can be used for navigation. The car alarm authorization code
for device-pairing is 0000. The ignition key must be on during the
pairing process.
If the car stands still for more than 10 minutes, GPS data
transmission may start with a delay of up to 1 minute.
11. Internet remote access
The web site www.GSMLink.cz enables car alarm remote control
(to users) and setting (to installers).
To get internet access to an installed and powered car alarm you will
first be asked to register your car alarm on the first page. You will find
a unique registration code for your car alarm on the warranty card.
12. Central monitoring station communication
The GSM communicator allows central monitoring via GPRS data
protocol. The central monitoring station (CMS) gets arming, disarming and
alarm information. It also regularly checks the communication link to the car
after it is armed. So if anyone tries to tamper with GSM communications, it
will indicate an alarm at the CMS.
13. Additional features
13.1. Car battery low voltage reporting
The built-in voltage drop detector can trigger an alarm if an electrical
device in the car is turned on while the car is armed. The sensor is
active 10 minutes after arming.
13.2. Passive guarding
Via the DIP I parameter it is possible to block the car against starting up
the engine, if the ignition key is turned off for 5 minutes and the alarm is not
set. The function can be turned off by pressing any key on the RC-8x
remote controller. It is also possible to set up the parameter to send a
STATUS SMS, which informs the user that the alarm is not set; in the case
that the ignition key is turned off for 60 minutes and the alarm was not set.
13.3. Remote siren activation
You can operate the siren remotely by the SIREN instructions. These
instructions are accepted from all authorized (stored) phone numbers.
Commands are also accepted from any unknown phone number if they
start with the USER code.
Instruction Status
SIREN ON activates SIR output permanently
SIREN OFF deactivate SIR output
SIREN activates SIR output for 30 sec.
SIREN xxM
or
SIREN xxxS
xxM – is a numeric value of the
duration of SIR output activation ,
in minutes
xxxS – as above, but in seconds).
13.4. Limited number of alarms
If any sensor (input) repeatedly triggers alarms then this particular input
will be bypassed automatically after the third alarm (it will remain bypassed
until the car alarm is disarmed).
13.5. LED indicator signals
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM network or a phone call
Regular slow flashing Armed
Regular fast flashing Alarm memory
Interrupted light Car was stopped (immobilization)
Flashing after ignition off GSM network is not available
Flashes after ignition on Number of enrolled remote controls
13.6. Pre-paid SIM card balance
It is recommended not to use prepaid cards in the car alarm. If you
have no other choice than prepaid cards, you can enable the CREDIT
instruction by the following sequence:
MASTER CREDIT uuu..u xx yyy zz
where: uuu…u is the provider’s code to obtain the balance
xx is the time period (in days) for regular checking
yyy is the threshold level below which the balance is
reported to the user (TEL1)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-1803BT - reset 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1803BT - reset 1 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1803BT - reset 1

Jablotron CA-1803BT - reset 1 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info