Manual Jablotron CA-1802 - Athos GSM RESET 1 (page 1 of 6) (English)

555040

Zoom out

Zoom in

1/6

GSM car alarm CA-1802 „Athos“ 1/6 MHF57202

Installation manual: CA-1802 “Athos” – mode 1

for cars without an original remote control for central locking

Main features for this mode:

 Remote control of car central locking (if installed) via a remote

control.



Sending alarm and information SMS messages to up to 4 mobile

phones.



Dialling pre-programmed phone numbers during alarms and

giving an acoustic warning signal.



Passing data to the central monitoring station.



Remote immobilization of the car via SMS instructions.



Remote control and programming of the alarm system from a

mobile phone.



Securing the vehicle’s goods area and the garage via up to 8 wireless

detectors of the JA-8x series.



Handsfree calling from the car and remotely listening-in to the car

(receiving of any incoming calls and dialling up to 4 pre-programmed

phone numbers).



Extension of functions via the CR-11A module, for example, operating

an independent car appliance via SMS (12V only).



Internet access and configuration from the www.GSMLink.cz web site.



Suitable for cars with a dashboard voltage supply of 12V or 24V.

1. Before installation

The auto-alarm should only be installed by a professional installer. It is

suitable for cars with a dashboard voltage supply of 12V or 24V with a

negative ground connection. During the first power-up, the value of supply

voltage is read and the inputs are set to default settings. The alarm is

designed to be installed inside the car.

The immobilizer relay contact of car alarm is connected only in disarmed

mode and if the ignition is on. Do not block circuits that are under voltage

while the ignition is off. It could cause a serious damage of the vehicle.

Disconnect the car battery before starting installation. For airbag-

equipped cars, no person is allowed to stay inside the car while handling

the battery. Disconnecting the battery can cause a reset of some of the

car’s devices (e.g. clock, default settings etc.). Avoid drilling into the metal

parts of the car body. The manufacturer is not responsible for damage

caused by any incorrect or unsuitable application of the product.

For crimping, special purpose tools should be used. If you do not use

some of the cables, cut them off at a distance of 10cm from the connector,

insulate them properly and tie them into a bunch.

For cars with a voltage supply of 24V, the following restrictions

apply to car alarm installation:

1. It is not possible to connect a hands-free set of type HF-03.

2. When used for acoustic signalling, the SIR output is switched to the

power supply voltage. Consequently, this output switches to 24V, so it

is necessary to use a siren of type SA-606-24V (instead of the siren

which is supplied in the standard package). In this case it is necessary

to set the confirmation beeps to 100 ms.

2. The wiring

Before installation, connect the wires as follows:

 Yellow – output siren – switches to +12V (24 V) / max. 1.3 A. It

signals an alarm (30 sec) and confirms control signals

 Gray – door switch input. It reacts to connection or disconnection

from ground . These switches should be fitted to all of the car’s doors.

 White – input INP1 – alarm input. It reacts to a connection or a

disconnection from the ground .

 Yellow-white – input INP2 – alarm input. It reacts to a connection or a

disconnection from ground. This input can trigger an alarm even if

disarmed (24 hour reaction).

 Blue – signals that the ignition key is turned on. Reacts to +12V

(24V) from the switch case. Make sure that a voltage is present in the

connecting wire while starting.

 Green – LED indicator – should be installed in a visible place on the

dashboard.

 White-black (position 10) – “Lock”, White-blue (position 11) –

„Unlock“ – Central locking control outputs. They switch to ground

(max. 200mA) with a selectable pulse length. For MODE 1, a pair of

wires with black shrinkable tube should be put into the connector. The

wires are equipped with black isolation diodes which protect the

functionality of cars with an intelligent central unit.

 Black – ground – connect to the original grounding point.

 Red – power supply +12V (24V) - connect directly to the battery. The

power should be turned on only after a thorough check of the whole

installation has been made!

 Orange – back-up battery – connects to a back-up battery of type BB-

02 (capacity 450 mAh, consumption up to 20 mA.)

 2x Brown – immobilization circuit (max. 8A constantly, 12A

intermittently).

 Pink – output AUX – an optional function of the output, see table 7 –

the power supply of external sensors is switched on by +12V/20mA or

by bus communication for CR-11A modules

this function is optional

It is possible to attach a hands-free set of type HF-03

. Using this you are

able to phone out from the car via the car alarm, and also to remotely listen-in to

the car after an alarm has been triggered or after the car has been immobilized.

The HF set connects to the RJ connector on the front side of the car alarm unit.

3. SIM card insertion

1. Make sure, that the PIN number on the SIM is disabled. If the SIM card

does not allow you to switch the PIN off, set the PIN to 0000. Remember

(note down) the phone number of your SIM card. It is recommended to

delete all original records in the SIM card’s phone directory.

2. Insertion of the SIM card: using a thin object, press the yellow peg in

order to pull out the SIM card holder (the front side of the alarm), insert the

SIM card into the casing with the conducting contacts facing up and push

the casing back carefully.

3. Install and attach the GSM antenna– (the car alarm must not be connected

to a power supply unless a GSM antenna is connected !!!). The antenna is

equipped with an adhesive tape and has to be stuck onto the car’s window or to

another suitable place like, for instance, below the upper part of the dashboard.

The antenna should not be installed close to the car alarm or near other

electronic devices. It is recommended to install the antenna in a place where it is

not easily visible (preferably in a tinted part of the window). Clear and dry the

spot carefully.

4. Check the wiring and connect the power supply. A flash of the indicator and

a beep of the siren indicate that the device is being connected to the GSM

network. Wait until the indicator turns off (up to 1 minute). After that the car

alarm is logged in to the GSM network.

If the flash does not disappear within 1 minute, it means that the login

process failed. If such a case occurs, turn off the power supply, pull out the

SIM card, ensure that the SIM contacts are clean, insert the card into a

mobile phone and check, whether a connection can be established in that

particular place. Also make sure that the SIM card‘s PIN is turned off (or that

it is set to 0000). If the mobile phone connection check is successful, return

the SIM card to the car alarm and repeat the whole procedure.

4. After turning the power supply on

In order to use the functionality of the car alarm according to your needs you first

have to setup its logic and behaviour by the RESET command. Subsequently,

phone numbers and other optional parameters should be set up and an RC-8x key

fob should be enrolled. The setup can be done in the following ways:

 by editing a record in the SIM card phone directory (it is the simplest

setting method but limited to some functions only, see table 5.1). These settings

(which determine the devices‘ behaviour) are read from the SIM card after each

powering up of the car alarm. After the initial powering up of the new car alarm

with a new (blank) SIM card, configuration records (names) are created in the

SIM card’s phone directory and the default values set. But in the case that the

alarm had been set before and a new (blank) SIM card is then inserted, then the

stored parameters are copied from the internal memory to the SIM card. This

will help you after SIM card changing. You can perform basic settings of some of

the car alarm’s functions by pulling the SIM card out of the alarm (after the

power supply has been disconnected) and subsequently inserting it into a

mobile phone where you assign numbers to the names of functions displayed in

the phone directory from the SIM. See table 5.1 for setting the car alarm’s

optional parameters. Settings from the SIM card are read after its insertion and

powering up.

 via the Internet page www.GSMLink.cz

which is the most convenient

way. To register there you need the registration code printed on the

warranty card and the master code (factory default is MASTER).

 by sending command SMS messages via a mobile phone, see table 5.1.

The choice of the correct car alarm mode should be made first. If you use

the car alarm in such a way that it is operated by its own key fobs, it is

necessary to select MODE 1. The settings can be done by storage in the

SIM card (put RESET into the phone directory as a name and add “1” to the

these accessories are optional

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1802 - Athos GSM RESET 1 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1802 - Athos GSM RESET 1

Jablotron CA-1802 - Athos GSM RESET 1 User Manual - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron CA-1802 - Athos GSM RESET 1 Manual

Product: