Manual Jablotron CA-1202 - mode 3 (page 1 of 2) (English)

555036

Zoom out

Zoom in

1/2

GSM pager CA-1202 „Athos“ 4/4 MHF52705

11 Internet remote access

The web site www.GSMLink.cz enables GSM pager remote control (to

users) and setting (to installers). The following features are enabled:

To get internet access to an installed and powered GSM pager you will

first be asked to register your GSM pager on the first page. You will find a

unique registration code for your GSM pager on the warranty card.

11.1 Reset GSM

If you need to disconnect and then reconnect the GSM module to the

GSM network, then use the command “MASTER RESET GSM”.

This does not affect any settings and is typically used for GPRS

activation or charging up credit. This command always requires the

Master code.

12 Central monitoring station communication

The GSM pager allows central monitoring via GPRS data protocol. The

central monitoring station (CMS) gets arming, disarming and alarm

information. It also regularly checks the communication link to the car after it is

armed. So if anyone tries to tamper with GSM pager communications, it will

indicate an alarm at the CMS.

13 Additional features

13.1 Car battery low voltage reporting

The GSM pager checks the voltage of the car battery. If the voltage is too

low (10V) it will notify users via an SMS message. This avoids complete

discharging of the car battery if you forget to turn off your lights etc.

13.2 Back-up battery

The GSM pager can be backed up by a BB-01 battery. Thus, the GSM

pager can keep sending information. Back up time is provided for several

hours. The manufacturer recommends regular BB-01 checking once a year.

The battery should be replaced every two years. Low voltage of the back up

battery (below 4V) is reported to the user via SMS (change the battery in this

case).

13.3 Car location

If your GSM provider offers a location service, you have to activate the

LOCATOR command after installation by the following SMS sequence:

MASTER LOCATOR xx…x

where: MASTER is the installers code

xx...x is the provider’s sequence to obtain the position

of the GSM pager SIM card (check with your

GSM provider for details)

After this sequence has been sent successfully once, the GSM pager

memorizes the parameters and from this moment on you can obtain the

location of the car by just sending the instruction LOCATOR.

Note: GSM location service may not be available in some countries.

13.4 Pre-paid SIM card balance

It is recommended not to use prepaid cards in the GSM pager. If you

have no other choice than prepaid cards, you can enable the CREDIT

instruction by following sequence:

MASTER CREDIT uuu..u xx yyy zz

where: uuu…u is the provider’s code to obtain the balance

xx is the time period (in days) for regular checking

yyy is the threshold level below which the balance is

reported to the user (TEL1)

zz is the position of the first digit of the balance in the reply

SMS from the provider

• After this sequence has been sent once, the GSM pager will check

the balance automatically every xx days and if the balance is lower

than yyy the user will be notified (TEL1)

• If the CREDIT instruction is enabled in the above way, the user can

also obtain the current balance by the instruction CREDIT

• To disable the automatic balance checking set the time period “xx”

to 00.

13.5 Roaming

If you travel abroad and your SIM card supports roaming, the GSM pager

will work there too.

13.6 Siren activation

If you are searching for a stolen car, you can operate the siren

remotely by the following SMS instructions:

MASTER SIREN turns the siren on for 10 minutes

MASTER SIREN ON siren on permanently

MASTER SIREN OFF siren off

To avoid misuse of this option, only an installer can switch the siren on.

13.7 LED indicator signals

LED state Meaning

OFF Disarmed

permanently ON connecting to a GSM network or a phone call

Regular slow flashing Armed

Regular fast flashing Alarm memory

Interrupted light Car was stopped (immobilization)

Flashing after ignition off GSM network is not available

Flashes after ignition on Number of enrolled remote controls

14 Specification

Power supply 12V DC (8-16V)

Stand-by consumption max. 10 mA

Max. consumption (during GSM communication) 1 A

GSM band 900 / 1800 MHz dual band system, power class 4

Transmitted power 2 W /GSM900, 1 W /GSM1800

VF frequency 433,92MHz

Working temperature -20°C to +70°C

Output SIR +12V, max. load 1,3A

Immobilization 8A permanently, 12A for 30 seconds

Central locking outputs max. 200mA, to GND

pulses 0,3s, 4s or 60s (optional)

Complies with ECE Rugulation No. 97.00, 10

Can be operated according to ERC/DEC98(20,21)

Health and safety ČSN EN 60950

EMC ČSN ETSI EN 301489-1, ČSN ETS 300683

radio interferences ČSN ETSI EN 301419-1, EN 301511, ČSN ETSI EN 300220

Hereby, Jablotron Ltd., declares that this CA-1202 is in compliance with the

essential requirements and other relevant provisions of Directive 1989/336/EC

and 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.com, section Technical support

Note: Although this product does not contain any harmful materials we

suggest you to return the product to the dealer or directly to the

producer after usage.

GSM pager CA-1202 „Athos“ 1/4 MHF52705

CA-1202 “Athos” installation manual

MODE 3 – GSM pager for cars with an installed car alarm

Main features for this mode:

• Sending of alarm SMS messages to up to 4 phones.

• Dialing and acoustic alarm warning to up to 4 phones.

• Location tracking of the car (using the triangulation feature of the

GSM provider)

• Central monitoring of the car when armed (fully supervised GPRS

protocol)

• Remote immobilization of the car via SMS instructions.

• Remote control of the alarm system and the central locking via SMS

instructions.

• Optional – Hands-free calling (receiving of any incoming call and

dialing up to four pre-programmed phone numbers)

• Remote internet alarm access (user and installer levels) via

www.GSMLink.cz

1 Before installation

The CA-1202 should only be installed by a professional installer. The

manufacturer assumes no liability for damages caused by incorrect

installation or use of this product.

The Athos GSM pager is suitable for cars with 12 V and negative

grounding. The main unit is designed for installation in the passenger

cabin.

Disconnect the car battery before starting installation; study the car

owner manual first. Avoid drilling into the metal parts of the car body.

Note: Use only proper crimping tools and parts to make connections. Cut

all unused wires and insulate them properly.

The thin wire which leads directly out of the central unit is the remote

control and wireless detector antenna. The location of this wire affects the

communication range. Place the antenna on a suitable plastic surface so

that the other wires do not screen it.

2 Wiring

• YELLOW – siren output (+12V / max. 1,3A).

• Gray – instant activation input reacts to connection or disconnection

from the ground (automatically recognizes logic).

• WHITE – INP1 input - reacts to connection or disconnection from the

ground (automatically recognizes logic). Reaction delay is 3 seconds

• BLUE –- ignition key input (+12V). Be sure, that there is +12V while the

key is on and while starting.

• GREEN – LED indicator – install it in a visible spot on the dashboard.

Connect the other end of this lead to the GND.

• BLACK – GND – connect to the original grounding in the car.

• RED – power supply +12V - connect directly to the battery. Check that

the installation is properly finished and that the GSM antenna is

connected before powering up!!

• ORANGE – back-up battery – connect a BB-01 optional battery

(Jablotron) if desired. If the BB-01 is not connected, then ground the wire.

• 2x BROWN – immobilization circuit (8A permanently, max. 12A /

3minutes).

• Pink – not used

3 SIM card insertion

1. Make sure, that the PIN password on the SIM is disabled. You can

do this using a mobile phone (e.g. for NOKIA: MENU, SETTINGS,

SECURITY SETTINGS, PIN CODE REQUEST, OFF). If your SIM card

does not allow switching the PIN off, change the PIN to 0000.

2. Activate the SIM card if necessary (see provider’s instructions),

ensure that it works (by a mobile phone) and record its phone number.

3. Using a thin pointed tool, press the colored button to release the SIM

cardholder. Insert the SIM card into the holder with the gold contacts

facing up and then reinsert the holder.

4 GSM antenna installation

DO NOT switch the power on before the GSM antenna is connected.

The provided antenna is adhesive and should be attached to the car window.

The antenna should not be obstructed by any metal parts. It is recommend to

install the antenna in a place where it is not easily visible (a tinted part of the

window, behind the mirror etc.). If the car has an original GSM antenna

installed, it can be used (if the connector is different, use an appropriate

adapter).

5 Initial powering-up of the GSM pager

Make sure, that the GSM antenna is connected, the SIM card inserted

and the wire harness installed properly. Then connect the power (car

battery). The LED indicator will turn on and the siren will make a short

chirp. Wait until the LED turns off (up to 1 minute).

If the LED starts to flash, no GSM network was found. In such a case

turn the power off, remove the SIM card and try to use it in a mobile

phone (at the place where the GSM antenna is). Check also if the PIN

protection is OFF (or set to 0000). If the SIM card logs into a network

successfully, reinsert it in to the pager and repeat powering-up.

After the GSM pager is powered up, you have to:

a) Select Mode 3 by the command RESET EN 3

b) Enroll remote controls (if used)

c) Set the programmable features (phone numbers, DIP, SET,

etc.).

These can be done by:

• SMS instructions – see table 6.1. For example sending an SMS:

MASTER RESET EN 1 to the GSM pager will select Mode 1.

• Internet page: www.GSMlink.cz

is the most convenient way. To

the warranty card) and the master code (factory default is

MASTER).

• SIM Card phone directory editing (see table 6.1 for list of features

which can be programmed this way). After the initial powering-up a

list of parameters is created in the SIM card phone directory. If you

then insert the SIM card in to a mobile phone, you can set

particular features (by entering numbers into the created list). The

entry for Mode setting is not automatically created, but it is possible

to make a new entry with the name: RESET EN and the number: 1.

Data entered this way are read by the GSM pager after the SIM

card is reinserted. For security reasons it is erased after reading.

6 Enrollment of remote controls

Up to 4 RC-40 remote controllers and can be enrolled to the GSM pager

(after Mode 3 is selected by the RESET EN 3 instruction).

Remote control enrollment:

1. Switch the ignition on

2. Send the SMS instruction: MASTER LEARN RC

• If the siren is connected to the GSM pager it will chirp 3x and the

LED will start flashing.

3. Press and hold buttons A and B together for 3 sec on the remote

control.

• A siren chirp confirms the enrollment.

• By enrolling the first remote control all other remote controls

previously enrolled will be erased (all the remote controls you

want to use must be enrolled during the same enrollment

session).

4. Exit enrollment by turning the ignition off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1202 - mode 3 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1202 - mode 3

Jablotron CA-1202 - mode 3 User Manual - English - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron CA-1202 - mode 3 Manual

Product: