555035
2
Zoom out
Zoom in
Previous page
1/2
Next page
CA-1202 User manual – Mode 2 - 2 / 4 – MHF53400
SMS instruction texts
Default Your text Description
AM
ARM
2
DM
DISARM
2
IMO
STOP (immobilize) the car (after turning
the ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
The car alarm will reply with status
information, e.g.
„car reports: Time: 27.01.04
13:04, Status: Armed, Unblocked, Ignition off“.
LOCATOR
To obtain the car location from the GSM
provider.
2
HELP
The car alarm will reply with a brief list of
SMS instructions.
CREDIT
To obtain the balance of a prepaid SIM
card if used.
2
UC xx...x
To change the user code. uuuu is the new
user code, up to 8 characters (A –Z & 0 –
9). The factory default user code is USER
Only basic ASCII can be used in the SMS instruction texts.
Ask the installer to edit the SMS commands for you.
After the HELP command the alarm will reply with the factory default SMS
instructions. The instructions that were modified will not be in the reply.
5. Remote blocking of the car
When the car alarm receives the SMS command IMO it will reply with a
confirmation SMS and block (immobilize) the engine. If the ignition key is on
when the car alarm receives the command IMO, immobilization will occur as
soon as the ignition key is switched off which will be confirmed by SMS.
Unblocking the car is only possible by the SMS instruction UNIMO.
6. Car location
If your GSM provider offers a location service you can obtain the location of the
car by just sending the instruction LOCATOR. The car alarm will reply e.g.
+420603012345 county: Jihocesky, District: Jindrichuv Hradec, Name: Nova Ves nad Luznici.
Distance 5.4 km. E14*52'1"@N48*50'24" + -200m 15:23:01 18.09.01
The alarm can send the location automatically in the case of an alarm or
immobilization by the IMO command
3
.
7. Remote control by dialing-in
The car alarm can be armed and disarmed remotely by dialing in from an
authorized phone (TEL1 to TEL4). The car alarm will not answer the incoming call,
2
Controlling by dialing in will result only in arming/disarming the alarm but it will not lock/unlock the
doors
3
Must be set by the installer
CA-1202 User manual – Mode 2 - 3 / 4 – MHF53400
but when it recognizes your number, it will change status (to Arm or Disarm). Such
remote control is free of charge since the phone is not answered.
Warning, if you dial your car alarm accidentally it can cause the alarm to disarm.
Controlling by dialing in will result only in arming/disarming the alarm but it will not
lock/unlock the doors
8. Phone calls by an installed hands free set
If the HF-03 hands free set is installed, it is
possible to receive and make phone calls via
the car alarm.
Incoming calls – to answer them, press any
button on the RC-40 remote control. By pressing
any button again, the call will be terminated.
To make a call – you can call up to 4
preprogrammed numbers while you are driving.
By pressing one of buttons A, B, 1 or 2 on the
remote control you will dial the corresponding
number (preprogrammed by the installer)
By pressing any button again, the call will be terminated. When armed, all
incoming calls are automatically rejected. If the car is blocked (by the IMO
instruction) all calls are automatically answered (it is then possible to listen to
and to speak to the car remotely).
9. Wireless detectors
It is possible to enroll up to 8 wireless detectors
(movement, glass-break, magnetic etc) from the Jablotron
JA-60 series to protect the area up to 20 meters away from
the car alarm. After arming the car alarm, an exit delay of 20
seconds is provided to all enrolled detectors (the detectors
are ignored during this delay). A 20 second entrance delay
after triggering a detector is provided by the detectors that are
switched to delay mode. In the case of an alarm, the siren will
sound for 30 sec., warning SMS messages (e.g. alarm in
garage) will be sent to all phones (TEL1 to TEL4) and these
phones can also be called with a siren sound. The system
also reports low batteries in a detector by SMS.
JA-60P movement
detector
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-1202 - mode 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1202 - mode 2 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1202 - mode 2

Jablotron CA-1202 - mode 2 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info