555034
1
Zoom out
Zoom in
Previous page
1/2
Next page
CA-1202 User manual – Mode 1 - 4 / 4 – MHF53300
11. Limited number of alarms
If any sensor (input) repeatedly triggers alarms then this particular input will be
bypassed automatically after the third alarm (it will remain bypassed until the car
alarm is disarmed).
12. Remote service
When it is necessary to change the basic settings of the alarm like phone numbers
etc you do not need to contact the installer. Instead it is possible to change settings
remotely.
13. Central monitoring station communication
The car alarm allows central monitoring via GPRS data protocol. Please ask your
supplier for details.
14. Roaming
If you travel abroad and your SIM card supports roaming, the car alarm will
work there too (the functions LOCATOR and CREDIT might be not available).
15. LED indicator signals
The LED indicator is used to show
the status of the alarm. Warning! If
the LED indicator starts flashing
fast after the ignition is switched
off, it will not be able to send any
messages nor call in the case of
an alarm
.
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM network
or a phone call
Regular slow flashing Armed
Interrupted light Car was stopped
(immobilization)
Flashing fast GSM network is not available
Your installer’s contact details:
CA-1202 User manual – Mode 1 - 1 / 4 – MHF53300
The “Athos” CA-1202 GSM car alarm
MODE 1
Thank you very much for buying our CA-1202 car alarm. Now you will always be able to
find where you left your car.
Jablotron Ltd.
1. Controlling the car alarm by RC-40
By pressing the A button you will arm the alarm and if central
locking is installed it will also lock. By pressing button B you will
disarm the car alarm. Buttons 1 and 2 can be used for remote
operating of the gate, garage door etc. Please ask your
installer for detailed information.
2. Acoustic signals
The car alarm informs you about its status by siren chirps. The
chirps for arming (1x),
disarming (2x) and arming with the
triggered input (4x) are optional. Warning!
If the GSM network is not available
while the car alarm is being armed it
will not be able to send any messages
nor call in the case of an alarm.
3. Alarm
When an alarm is triggered (the car alarm is armed and an input is triggered), the
siren will sound for 30 sec., warning SMS messages will be sent to all phones
(TEL1 to TEL4) and these phones will also be called with a siren sound
1
. The
alarm can be terminated by pressing button B on the remote control or by SMS
instruction. Your mobile will be sent a message stating that the alarm
condition has ended.
4. Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4)
can operate the alarm remotely. Factory default instruction texts
are shown in the following table. If an SMS is sent from an
unauthorized phone a valid user code must be entered before the
instruction (e.g. USER IMO).
1
If it is activated ,then in the case of an alarm all calls are automatically answered
(it is possible to listen and speak to the car remotely).
Chirps Meaning
1 x Arming
2 x Disarming
3 x Disarming after the alarm
4 x Arming with the triggered
input
6 x GSM network is not available
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-1202 - mode 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1202 - mode 1 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1202 - mode 1

Jablotron CA-1202 - mode 1 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info