555033

Jablotron CA-01 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
CA-01 Car Alarm „Pulse“ 2 / 2 MDM51401
Advanced Installation, optional functions setting
The basic installation can be extended for a more advanced system.
An additional siren - can be installed into the passenger compartment.
Connect the positive pole of the siren (we recommend model SA-107) to
the green wire of the CA-01 and the negative pole to the ground. If an
alarm is triggered, the additional siren will sound for 1 minute. It can also
sound for 10 minutes, depending on the immobilization duration setting.
The additional siren can be combined together with the external
immobilization relay (limited by maximal total current output of 800mA on
the green CA-01 output) .
A Wireless Pager - can be used to transmit an alarm information to user.
We recommend pager PG-4W. The green CA-01 output (+12V when
alarm) is used to trigger paging (see pager instructions for more details
regarding its installation).
An Immobilization relay - is a suitable solution for increasing your car’s
security. Connect the additional relay (we recommend model RA-12/30A)
coil contacts between the green CA-01 output and the ground. The
Normally Closed relay contact can be used to disable the engine (the
starter control circuit, for example).
If an alarm is triggered, this relay will disable the selected circuit for 1 or 10
minutes (selectable). Immobilization is indicated by the LED being
continuously light. There is no way to switch off the immobilization before the
selected time period elapses. Pay high attention to the quality of
immobilization circuit connections. Any failure in this circuit can result in a
poor or dangerous car performance.
no. siren chirps
optional function factory default
do not use ign. key to keep
you can select
switching on and off the key
• • • • • • • • • • • • • • • •
setting mode
LED status
z
LED status
5
1
•
entrance delay duration
15 seconds 10 seconds
2
• •
exit delay audible indication (ticking)
enabled disabled
3
• • •
vibration detector reaction
Alarm Warning
4
• • • •
vibration detector function
enabled disabled completely
5
• • • • •
immobilization duration (+12V on green
output)
1 minute 10 minutes
6
• • • • • •
current consumption detector
enabled disabled completely
• • • • • • • • • • • • • • • •
exit of the setting mode, data is stored into the memory (EEPROM)
Hidden Button Arming - if you do not want to use the ignition key for
arming, install a push button switch in a hidden location. Connect the blue
CA-01 input wire to this switch so that there is +12V on the input if the
button is pressed. The arming logic is the same (press twice for arming,
once for disarming).
Note: If you use the hidden button for arming, disable only the starter with
the immobilization relay. This will prevent an accidental immobilization
when driving.
A Warning Function - the vibration detector function can be switched
from the alarm trigger to a warning trigger (see setting mode). If the
warning function is selected, any detected vibration will result only in a
short siren chirp when is CA-01 armed. The digital filter will not filter out
independent vibrations.
The vibration detector can also be completely disabled in the setting
mode.
Setting mode
Optional functions can be modified in this mode. Read the following
descriptions, then enter the setting mode:
1) disconnect the CA-01 power (red wire)
2) turn on the ignition key
3) wait 1 minute then reconnect the power
4) switch the ignition key off and then switch it on and off five times
5) the siren will make 16 short chirps indicating that the setting mode
was entered
The car alarm will automatically offer one optional function every
3 seconds (see the following table). The number of the function (row
number in the table) is indicated by number of the siren chirps.
If you want to select the offered function, switch on and off the ignition
key (LED goes off). If you do not want to select the offered function, wait
until the CA-01 will offer the function you want to modify.
After all functions are offered, the CA-01 will close the setting mode
automatically (confirmed by 16 siren chirps. All data is stored to the
memory). If you do not select any offered function in the setting mode, the
car alarm will return to the factory default settings.
Note: If you switch the ignition key on for longer than 10 seconds in any
offered function level, the setting mode will be terminated and no changes
will be stored to the memory.
Vibration detector testing
If you want to test the built-in vibration detector sensitivity, perform steps
no. 1, 2 and 3 of the setting mode entering (see above). After power
reconnecting leave the ignition key on and you can test vibration detector
now (triggering is indicated by a LED flash and a siren chirp). Switch off
the ignition key for more then 10 seconds to exit testing mode.
Note: Although this product does not contain any harmful materials we
suggest you to return the product to the dealer or directly to the producer
after usage.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-01 in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info