578910

Irox HELVET-X Manual

11
Zoom out
Zoom in
Previous page
1/12
Next page
~P.11~
(E)
Very Weak Weak Medium Strong
[ ] button
Increases the value of a setting
Enable or disable the alarm when in Alarm display mode
[ ] button
Decreases the value of a setting
Activates manual synchanization for radio frequency
[ RESET ] button (inside battery compartment)
To activate system reset during abnormal condition.
B. DCF77 Radio Controlled Clock
The radio-controlled time is calculated by the Cesium Atomic clock of Braunschweig
(official clock of Germany). Then the time is coded and transmitted from Mainflingen
- near Frankfurt - via a signal on DCF-77 (77.5 kHz). The transmitting range of the
signal is 1500 km, which means that most of Western and Central Europe is covered
by this signal. Within this range the received time is completely accurate. Once sensor
signal(s) are received, the wave icon will flash to indicate that the receiving unit starts
to receive the DCF radio controlled time signal.
Radio Controlled wave icon can indicate 4 levels of signal status:
Once the time signal is received, the wave icon will stay on the LCD, and time and
calendar will automatically be updated.
Note: During 10 minutes of time signal reception, all manual settings will be sus-
pended. If setting is desired, press once [ ] key to deactivate the reception. You can
also press and hold the same key for 3 seconds to manually activate the reception in
normal mode.
C. Setting the clock, multi language, calendar, and temperature unit
1. Press & hold [MODE] button for 2 seconds. 12Hr/24Hr is blinking.
2. Use [ ] or [ ] button to select 12 or 24 hour format, then press [MODE] button to
confirm.
3. The hour digits will blink. Use [ ] or [ ] button to set the required time (each press
the button will increase or decrease the digits by one. Holding the button will cause
the setting to change rapidly). Press [MODE] button to confirm.
4. The minute digits will blink. Repeat the same procedures to enter minutes, Year
(range from 2005 to 2099),Date/Month or Month/Date format, current Month or Date
(Weekday auto selection), languages and °C or °F selection.
D. Setting the alarm
1. Press [ALARM] button once to switch from clock mode to display the alarm time, press
again to switch back to clock time display
2. Press [ALARM] button to display alarm time. Press & hold [ALARM] button 2 seconds
to enter alarm setting mode. The hour digit will blink.
3. Use [ ] or [ ] button to set the desired hour. Press [ALARM] button to confirm.
4. The minute digit will blink. Use [ ] or [ ] button to adjust minutes, and press [ALARM]
button to confirm.
5. The “%” bell icon will be shown to indicate the displayed alarm time is enable.
6. When the alarm is beeping, press [SNOOZE/LIGHT] button once to temporarily stop
the alarm for 10 minutes.
7. Press any button to stop the alarm (except [SNOOZE/LIGHT] button).
… 11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Irox HELVET-X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Irox HELVET-X in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info