632874
30
Zoom out
Zoom in
Previous page
1/31
Next page
How Verro Works
iRobot Verro uses a powerful motor to
draw 80 gallons of water per minute
through the filter bag. This creates strong
suction at two inlet ports under the
robot that draws dirt and debris, such as
bacteria, algae, leaves, and even coins
into the filter bag where they are trapped.
The pump motor also drives two high-
pressure jets under the robot that loosen
dirt and attached particles, which are
then vacuumed up.
Verro uses the force of the water being
pumped through the robot to hold itself
against the surface it is cleaning and to
move along it.
Each time it changes direction, Verro
automatically alters it course slightly so
that it covers the entire bottom and sides
of the pool efficiently.
iRobot
®
Verro
model 300 Quick Start Guide
Instructional photos available at www.irobot.com/usetips
Tip
Clean the filter bag regularly. Verro uses
the force of the water pumped through
its filter bag to move properly. If the
filter bag is not kept clean, Verro will
not move or clean properly.
Tip
Store Verro in a dry place out of direct
sunlight at a temperature between
50 and 104 degrees Fahrenheit. The
Power Supply is water resistant, but not
waterproof and may be damaged by rain.
Important: Failure to properly store Verro
will result in loss of warranty.
Tip
iRobot recommends using the mesh
filter bag (included) when
the pool contains a significant quantity
of large debris (leaves, etc.), such
as when the pool is opened for the
season. The fine filter bag is ideal for
filtering small debris (algae, sand,
etc.) and for regular maintenance.
Tip
Periodically straighten the floating
power cord with the Detangler.
Tip
Verro’s Power Supply has an automatic
timer that shuts Verro OFF after
approximately two hours of operation.
When this happens, the power switch
will remain ON. To start another
cleaning cycle, switch the Power
Supply OFF and then back ON and
then press the reset button.
1
Uncoil the floating power cord and spread it over the surface of the water, ensuring that it is not tangled
or kinked.
6
Set the time control dial to 30 seconds.
2
Place Verro upside down in the pool and rock it from side to side to allow air to escape. Turn Verro over
and allow it to sink to the bottom of the pool so that the wheels rest on the bottom of the pool.
Warning: A Ground Fault Current Interrupter (GFCI) must be installed to
protect your electric outlet and prevent any possible electric shock.
7
Turn the Power Supply switch ON then press the reset button. The light on the Power Supply will
illuminate and Verro will start to clean your pool.
3
Place the Power Supply in a dry area at least 3.5 meters/12 feet from the pool.
5
Ensure that the Power Supply is at least 12 feet from the pool and that the power switch is OFF. Plug
the Power Supply into a GFCI outlet. Ensure the electric outlet has been properly grounded.
Never leave the Power Supply plugged in when Verro is not in use
4
Plug the floating power cord into the Power Supply. Be sure not to force the plug as it will only
go in one way.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Irobot Verro 300 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Irobot Verro 300 Series in the language / languages: English as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info