Manual Ion QUICK PLAY FLASH (page 3 of 20) (English, German, Dutch, French, Italian, Spanish)

519238

Zoom out

Zoom in

1/20

* If needed, you may adjust the speed of the

turntable platter by tightening/loosening the

appropriate screw (there are separate screws

for 33/45/78 RPM operation on the underside

of QUICK PLAY FLASH) with a standard

Phillips-head screwdriver.

FRONT PANEL

1. VOLUME - hold down "-" or "+" button to increase/decrease volume;

2. MODE - enters Playback or Record Mode. Press this button firmly for

about half a second -- don't just tap it.

3. FORWARD/BACK - moves to the previous/next track on the flash drive

f / /  - Play, Pause, and Record functions.

See PLAYBACK/RECORDING section for more information.

• Solid red light: Ready to record (Record Mode).

• Flashing red light: Recording a song.

• Solid green light: Ready to play (Playback Mode).

• Flashing green light: Playing a song.

5. USB PORT - connect a USB flash drive here

REAR PANEL

1. RCA OUTPUT – Line-level coaxial output; do not

connect to phono-level inputs (on a receiver).

Note: You must be in Record Mode to hear audio

through these outputs when playing a record.

2. USB – Connect to a computer to record audio

with EZ Vinyl/Tape Converter; (QUICK PLAY

FLASH can not be USB-powered; this must use a

power adapter). Use the included USB Cable to

connect your turntable to your computer. For

transferring your vinyl records to your computer,

we have provided software on the included CD.

3. PHONES – Connect 1/8" stereo headphones here (not included). The RCA outputs stop playing audio once

headphones are connected.

4. 33/45/78 RPM SWITCH – Sets speed of the platter

5. Autostop Switch – This switch turns autostop on or off.

When autostop is on, the platter will start spinning when

the tonearm is placed over the record and stop spinning

when the record has reached the end. (When autostop is

off, the platter will always spin regardless of the position of

the tonearm.)

Note: If your record stops before a song is done playing, set the Autostop Switch to "off."

6. POWER - Use included adapter to connect to wall power (9V DC, 800mA, pin +, tip –).

PLAYBACK/RECORDING

HOW TO PLAY YOUR RECORDS

1. Place the record on platter.

2. Select speed (33/45/78 RPM); use the included 45 RPM adapter if needed.

3. Undo the armclip.

4. Use the Raise/Lower Lever to raise the tonearm, then move it over to the record.

5. Lower the tonearm onto record; the record will begin playing.

6. Adjust volume with VOL buttons or your speaker system.

7. When finished, raise the tonearm and return it to rest on the armclip.

HOW TO RECORD TO A FLASH DRIVE

1. Connect a USB flash drive to the turntable’s front USB port.

2. Follow Steps #1-3 in HOW TO PLAY YOUR RECORDS (above).

3. If the light next to the f / /  button is lit solid red, proceed to Step 4. If it is lit green, press the Mode button

once.

4. To start recording, press and hold the

f / /  for about 2 seconds; the light will flash red, indicating it's

recording.

5. Lower tonearm onto the record; the record will play and the song will record.

6. When finished, press

f / /  for about 2 seconds to stop recording.

7. To record more songs, repeat Steps #2-6 above. When you are finished, raise the tonearm and return it to the

armclip.

MODE

f / / z

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ion QUICK PLAY FLASH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ion QUICK PLAY FLASH Manual

Product: