686584
20
Zoom out
Zoom in
Previous page
1/21
Next page
275
A
S AVE THESE INSTRUCTIONS
(275IO) SPA (JET + HARD WATER) ENGLISH 7.5” X 10.3” PANTONE 295U 07/15/2016
English
TROUBLESHOOTING
Page 20
PROBLEM CAUSE SOLUTION
NO DISPLAY/SPA
CONTROL UNIT DOES
NOT WORK
Spa is unplugged or off.
Control panel cable plug loose.
Power failure.
RCD tripped.
RCD broken.
Ensure the spa is plugged and switched on.
• Ensurethecontrolpanelcableplugisrmlyattached
to the control base receptacle.
Check power source.
Reset the RCD.
Contact Intex Service Center.
HOUSEHOLD CIRCUIT
BREAKER TRIPPED
Circuit breaker under rated.
Overloaded circuit breaker.
An electrical fault in the line.
Ensure correct circuit breaker rating.
Provide a dedicated circuit breaker feeding the spa
electrical outlet only.
Contact a qualify electrician to correct the electrical fault.
NOT HEATING
PROPERLY
Temperature set too low.
• Dirtyltercartridge.
Water temperature decreasing during
heater STANDBY mode.
Heating element failed.
Increase the temperature and attach the spa cover.
• Cleanorreplacetheltercartridgeintime.
• IfheaterisinSTANDBYmode,presstheamebutton
twice to heat up the water to the set temperature.
Contact Intex Service Center.
JET FUNCTION DOES
NOT WORK
Jet pump is too hot. Turn off and unplug the spa. Let it cool down and
restart all over again.
If problem persists contact Intex Service Center.
JET OUTPUT IS WEAK
Low water level.
Obstruction in the suction inlet inside the tub.
Jet nozzles clogged or dirty.
Jet nozzles plumbing pipes damaged.
Add water between MIN and MAX level.
Ensure suction inlet is not covered or blocked.
Clean any dirt inside the jet nozzles.
Contact Intex Service Center.
JET AIR CONTROL
KNOB NOT WORKING
Jet nozzles clogged or dirty.
• Jetairowplumbinginsidethespatub
damaged.
Clean any dirt inside the jet nozzles.
Contact Intex Service Center.
FILTRATION PUMP
NOT WORKING
• Dirtyltercartridge.
Filtration inlet and/or outlet clogged.
Filter pump motor failed.
• Cleanorreplacetheltercartridgeintime.
• Checkandcleanltrationinletandoutletregularly.
Contact Intex Service Center.
WATER NOT CLEAN Cartridge assembly not properly attached.
• Insufcientlteringtime.
• Dirtyltercartridge.
Improper water maintenance.
Filtration inlet and outlet clogged.
Ensure the cartridge assembly is properly attached.
• Increaseltrationtime.
• Cleanorreplacetheltercartridgeintime.
Keep the spa water properly sanitized. Refer to the
chemical manufacturer’s instructions.
• Checkandcleanltrationinletandoutletregularly.
PUMP CONNECTORS
ARE NOT LEVEL WITH
THE SPA CONNECTORS
One characteristic of PVC is that
it changes shape, which is normal.
Elevate the pump with wood or another type of
insulated material to bring the pump’s connectors
level with the spa’s connectors.
TUB HAS A STRANGE
SHAPE
Expanded internal air pressure by
strong sunshine.
Do not expose the spa to direct sunlight for extended period of time.
Check the air pressure and release air if necessary.
During very hot weather, you must check to see whether it is
necessary to release some air. This is to avoid any possible damage
to the tub.
TUB LOSES AIR
PRESSURE
Air valve cap loose.
Air valve base loose.
Hole, cut or split on spa tub.
Ensure air valve cap is securely closed.
Fill up the spa tub with air then make sure the air valve
base is tighten, see “Spa Tub Air Valve Fastening” section.
Put liquid soap and water in a squirt bottle and spray
onseams.Ifthereisaleakitwillbubble.Afteryound
the leak, clean and dry the leaking area, then apply the
repair patch that comes with your spa.
LEAKING BETWEEN
SPA TUB CONNECTORS
AND CONTROL UNIT
CONNECTORS
Spa control base inlet/outlet connections
not securely tight.
Spa control base inlet/outlet o-ring
missing/dirty.
Tighten inlet and outlet connections.
Coat the o-ring with petroleum jelly for water proof.
SPA IS TOO NOISY
IN FILTRATION MODE
ONLY
Control base components not securely
attached.
• Controlbasegroundnotlevelandrm.
• Spaltermotorfailed.
Ensure control panel, back cover and all inlet/outlet
are securely connected.
• Ensuregroundislevel,rmandsmooth.
• Replacethefailedltermotorwithanewone.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa SPJ-H-22-1G - 28436 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa SPJ-H-22-1G - 28436 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa SPJ-H-22-1G - 28436

Intex PureSpa SPJ-H-22-1G - 28436 User Manual - Dutch - 22 pages

Intex PureSpa SPJ-H-22-1G - 28436 Additional guide - All languages - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info