752330
26
Zoom out
Zoom in
Previous page
1/29
Next page
188
NL
SAVE THESE INSTRUCTIONS Page 2
English
(188NL) MODEL CS7220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 09/28/2012
SAVE THESE INSTRUCTIONS Page 26
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
INSUFFICIENT
CHLORINE
INSUFFICIENT
COPPER ION
LEVEL
POOL IS STAINED
WHITE FLAKES IN
THE WATER
NO LED DISPLAY
GREEN HAIR
Insufficient operating hours of
the Saltwater System.
The salt level in the pool water
is less than 2000ppm. This is
insufficient.
Chlorine loss due to intense
sunlight exposure.
The bather load has increased.
Clogged or dirty electrolytic cell.
High UV level exposure.
Insufficient operating hours.
The PH is too high.
The bather load has increased.
Clogged or dirty copper electrode.
Copper electrode defective.
High copper ion concentration.
Excessive calcium hardness is
present in pool water.
No power supply.
RCD/GFCI has not reseted.
A power fuse has blown.
LED failure.
High copper ion concentration.
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
Check the salt level with the Test Kit. Adjust
as needed. See “Salt & Pool Water Volumes”.
Use a pool cover when the pool is not in use
and/or when the unit is operating.
Increase the daily Saltwater System operating
time. See “Operating Instructions”.
Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
Cover the pool with a pool cover for 2 days with
the device running and then test the water
using the test strips.
If the pool is clean and clear, add stabilizer to
the water and then test the water with the
device running.
Increase operating time per day. See
“Operating Instructions”.
Use PH decrease chemical to adjust,
contact your local pool chemical store.
Increase the operating time per day.
See “Operating Instructions”.
Remove the cell for inspection, clean it
if necessary. See “Maintenance”.
Contact Intex Service Center.
Drain about 20% of the pool water and add fresh
water to decrease the copper ion concentration
below 0.2ppm.
Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
need around 3g (1000 gals need 0.4 ounce)
to pool.
Use a lemon based cleaning product (preferably
containing citric acid). Don’t scrub with aggressive
cleaning products because this might etch the
underlying surface.
Drain about 20 to 25% of the pool water and add fresh
water to decrease the calcium hardness. Inspect the
electrolytic cell for scale buildup. Clean the electrolytic
cell if necessary.
Plug the cell cord firmly into the cell
housing receptacle.
Find out the switch and turn on.
Reset the RCD/GFCI.
Contact Intex Service Center.
Drain about 20% of the pool water and
add fresh water to decrease the copper
ion concentration below 0.2ppm.
Add aluminum sulfate: 1000 liters
water need around 2g (1000 gals need
0.27 ounce) or aluminum potassium
sulfate: 1000 liters water need around
3g (1000 gals need 0.4 ounce) to pool.
Use ‘Ultra-Swim’ shampoo, or shampoo
containing chelating agents.
PROBLEM CAUSE SOLUTION
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Krystal Clear - CS7220G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Krystal Clear - CS7220G in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Krystal Clear - CS7220G

Intex Krystal Clear - CS7220G User Manual - German - 29 pages

Intex Krystal Clear - CS7220G User Manual - Dutch - 30 pages

Intex Krystal Clear - CS7220G User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info