686082
15
Zoom out
Zoom in
Previous page
1/18
Next page
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/21/2012
110A
SAVE THESE INSTRUCTIONS
Page 15
English
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
THE WATER FLOW
IS VERY SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
The motor is not plugged in.
The Fuse box needs checking.
The GFCI/RCD circuit breaker
is tripped.
Motor too hot and overload
protection is shut off.
Improper chlorine or pH
levels.
Filter cartridge is dirty.
Damaged cartridge.
Excessively dirty pool.
The strainer screen is
restricting the water flow.
Clogged inlet or discharge.
An air leak on the intake line.
Scale or buildup on cartridge.
Excessively dirty pool.
Dirty filter cartridge.
The nozzle and strainer
connection are reversed.
Low water level.
Strainer screen plugged up.
An air leak on the intake hose.
Faulty motor or the impeller
is jammed.
An air lock inside the cartridge
chamber.
O-ring missing.
Cover is not tight.
Filter cartridge is dirty.
Hose nuts are not well-fitted.
There’s air trapped in the
pump housing and inlet hose.
The inlet and outlet hoses
connection are reversed.
TROUBLE CAUSE SOLUTION
Filter cord must be plugged into a 3
wire outlet that is protected by a Class
A Ground Fault Circuit Interrupter, or
RCD.
Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
Let the motor cool down.
Adjust the chlorine and pH level. Consult
your local swimming pool supply stores.
Clean or replace cartridge.
Check the cartridge for holes. Replace
if damaged.
Operate the filter for longer periods.
Clean the strainer screen at the inlet.
Clear any obstructions in the intake
hose by discharging it inside pool wall.
Tighten hose nuts, check hoses for
damage, check pool water level.
Replace cartridge.
Clean cartridge more often.
Clean inside the plunger valve.
Pull valve handle to full upright position.
Install the nozzle at the upper position
of pool inlet, and the strainer at the
lower position of pool outlet.
Fill pool to correct water level.
Clean strainer screens at pool inlet.
Tighten hose nuts, check hose for
damage.
Clear any sticks or leaves in the
intake hose.
Turn and pull valve handle to full upright
position.
Remove cover & check for O-ring.
Tighten cover (Manually).
Replace or clean cartridge.
Tighten or reinstall hose nut.
Open air release valves, wait until water
starts to flow out of the valves, then
close it.
The lower position of pool outlet
connects to filter pump water inlet. The
upper position of pool inlet connects to
filter pump water outlet.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Krystal Clear - 634T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Krystal Clear - 634T in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Krystal Clear - 634T

Intex Krystal Clear - 634T User Manual - German - 16 pages

Intex Krystal Clear - 634T User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info