686079
26
Zoom out
Zoom in
Previous page
1/28
Next page
329
A
SAVE THESE INSTRUCTIONS
English
(329IO) MODEL ECO 5220/5230 & 6220/6230 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/05/2018
Page 26
TROUBLESHOOTING GUIDE (continued)
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service Department for
assistance. See separate “Authorized Service Centers” sheet.
1. Filter pump not attached to
system and/or switch on.
2. Circulation line is blocked.
3. Incorrect inlet and outlet hose
direction.
4. Scale on the flow sensor.
5. Flow sensor cord is loose.
6. Inner timer conflict between
filter pump and saltwater system.
7. Flow sensor failure.
1. Dirt or scale on titanium plates.
2. Low salt level / No salt.
3. Electrolytic cell cord is loose.
4. Possible electrolytic cell failure.
1. High salt level.
1. LED display is off and the “SERVICE”
light is on - the system does not power
up.
2. Caused by high humidity.
3. PCB failure.
Ensure filter pump is attached and
operating. See "Setup Instruction".
If your unit has plunger valves, ensure
that they are open.
Clear your filter cartridge and cell from
debris and dirt. See “Maintenance”.
Release all trapped air in the circulation
line. See the filter pump manual.
Check the direction of the inlet and the
outlet hose. Reverse the hoses if
necessary. See “Set Up Instructions”.
Clean the flow sensor, paying special
attention to the hinge. See “Maintenance”.
Plug the flow sensor firmly into the flow
sensor receptacle.
Reset both timers on the filter pump and
saltwater system.See “Boost Cycle”.
Contact Intex Service Center.
Remove primary electrolytic cell for
inspection. Clean it if necessary. See
“Maintenance”.
Add salt. See “Salt & Pool Water Volumes”.
Ensure that the cell cord is plugged
firmly into the cell housing receptacle.
Contact Intex Service Center. Replace
the cell if needed.
Partially drain the pool and refill it with
fresh water. See “Salt & Pool Water
Volumes”.
Household voltage is too high or too low (+ 20%).
Check the voltage is within the range stated on the
device housing.
Run the system during midday and avoid running
it during dawn, foggy or raining time. Place a piece
of tile or similar pad, 15”x15” (38x38 cm) in size,
between the device and the ground to keep ground
water evaporation away from the system.
Contact Intex Service Center.
LED PANEL
CODE PROBLEM SOLUTION
LED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex ECO6220G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex ECO6220G in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex ECO6220G

Intex ECO6220G User Manual - German - 28 pages

Intex ECO6220G User Manual - Dutch - 29 pages

Intex ECO6220G User Manual - French - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info