686602
11
Zoom out
Zoom in
Previous page
1/14
Next page
(114) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 05/30/2012
114A
SAVE THESE INSTRUCTIONS Page 11
English
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
Plug in the power cord.
Switch the knob clockwise to the "I"
position to turn the electric pool
heater on.
Re-plug the GFCI/RCD and press the
“RESET” button.
The temperature sensor will cut off
the power of heater when the water
temperature is above approximately
95oF (35°C). It continues to work
when the water temperature drop
below approximately 82°F (28°C).
Turn on the filter pump.
Ensure the plunger valves are opened
(if any).
Ensure your filter cartridges are clear
from debris and dirt.
Release all trapped air in the
circulation line.
Check for the direction of water inlet
and water outlet hose. Reverse the
hose if necessary.
Always use the solar cover if the pool
is not occupied.
Increase the heating time properly.
Stop the heater and shorten the
heating time.
Tighten/reinstall hose clamps.
Reposition/replace hose seals.
Unplug the GFCI/RCD and then
re-plug in and press the “RESET”
button to start the heater. Contact
Intex Service Center if it trips off
continuously.
THE RED
INDICATOR DOES
NOT LIGHT UP
DURING USE
THE WATER
TEMPERATURE
DOES NOT
INCREASE
ALTHOUGH THE
RED INDICATOR IS
LIT UP
THE WATER
TEMPERATURE IS
TOO HIGH
HOSE LEAKING
GFCI/RCD KEEPS
TRIPPING OFF
1. The power cord is not
plugged in.
2. The knob is not fully switched
to on position – “I”.
3. The GFCI/RCD plug is not
turned on.
4. The water temperature is too
high.
5. No water flow.
6. Low water flow.
1. Pool or solar cover not been
used.
2. The pool size or water capacity
exceeds the heater capacity.
3. The water temperature is too
low.
1. Heating time too long.
1. Hose clamps.
2. Hose seals.
1. Product failure or electrical
circuit problem.
PROBLEM CAUSE REMEDY
The white inserts at both ends of the hoses shall remain inside and shall be
firmly inserted in the hose. Do not remove the white inserts from the hoses.
These white inserts are not serviceable parts.
To facilitate the connection of the hoses into the black protruding hose
connectors on the pool wall, you may use soapy water solution (mix 6 drops
of dish detergent in 1/2 a cup of water) to lubricate the inserts by simply
dipping the hose ends into the solution. Continue per owner’s manual.
Do not use lubricants such as machine or industrial oil or grease.
HOSE
INSERT
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex 28684 - HT30220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex 28684 - HT30220 in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex 28684 - HT30220

Intex 28684 - HT30220 User Manual - German - 14 pages

Intex 28684 - HT30220 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info