609974

Inner Range Concept C4000 Controller Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Turn Area/s ON or OFF.
Once you have Logged on to a Terminal, and see the Area status with the “Push
Off” or “Push On” message, you may perform the ON or OFF operations.
At the prompt, turn the displayed Area (or Area List)
OFF or ON by pressing the appropriate key.
Remember: You have a limited time to turn an Area
OFF once you have entered, and a limited time to
exit when you have turned an Area ON.
If you are allowed to control multiple Areas:
-DISPLAY MODE. The Display mode can be
changed from Single Area to Area List and vice
versa, by pressing the Right Arrow key.
-AREA SELECTION. You may select other Areas or
Area Lists by using the Up and Down Arrow keys or
the letter key that the Area name begins with.
After pressing the ON key, the display may show a
message like this. It means that the item displayed
is either faulty or in an alarm state, and the Area will
not turn ON.
Try and rectify the problem before trying again.
If this is not possible, You may be allowed to
ISOLATE the item while the “Zone Problem”
message is displayed, by pressing the OK key.
Access (Un-lock) a Door.
Terminals may be programmed to momentarily Unlock a Door to allow access.
  
  
 



Logon to the Terminal as described earlier.
(PIN + OK) Area Status will display as before.
Press OK a second time to perform the Door
Access operation. (Not necessary for
Terminals/Users designated as “Access Only”)
The display will verify that the operation was
successful, or provide a message showing why
the operation could not be performed.
  
  
 



Acknowledge an Alarm.
Alarm messages must be acknowledged by a User with the appropriate authority.
These messages provide precise information of the type of alarm, the Area it has
occured in, and the Zone or System Input that generated the alarm.
An Alarm message may be displayed on the
Terminal, and indicates which Area the Alarm
has occured in.
Logon to the Terminal as described before.
(PIN code + OK)
The display will show the specific details of the
Alarm and provide a scrolling message if more
than 16 characters.
e.g. “Had Alarm on FRONT DOOR in FOYER”
Note alarm details, then press the OK key to
acknowledge the message. The display will
now show the Area ON / OFF message to allow
you to continue with your operation.
e.g. Turn the Area OFF.






 
 
 



LOGOFF the Terminal.
When you have completed your operations, you must Logoff the Terminal.
Press the END key. (END also lets you start
again, if you make an error entering your PIN)
or
- - - ,
- - - ,
NOTE: Quick Arm/Disarm. Your system may be configured to allow a nominated
Area to be controlled simply by entering your PIN code, then the OFF or ON key.
i.e. OK key not required. (V7.8 or later only with LCD Terminal V8.3 or later)
LOGON to an LCD Terminal.
Logging on is the first step performed in most operations.
  
  
 
  
  
 






- - - ,
Enter your secret PIN code using the digit keys,
then press the OK key.
If there are no messages to be acknowledged, the
Display will first greet and identify you.
(Note: Greeting option can be disabled if required)
The status of the first Area (or Area List) that you
are allowed to control is displayed, with a prompt to
perform an ON or OFF operation.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inner Range Concept C4000 Controller at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inner Range Concept C4000 Controller in the language / languages: English as an attachment in your email.

The manual is 0,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info