Manual Indesit IDE1000 (page 12 of 13) (English)

46872

Zoom out

Zoom in

1/13

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned

to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher,

making it level. In any case, the appliance should not be

inclined more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

This dishwasher model can be built under a single worktop

(please read the relevant instruction sheet).

Cold Water Connection

This electric household appliance should be connected to

the water mains using the cold water supply hose provided

with the appliance only. Do not

use a different hose. In the

event of replacements, use

original spare parts only.

Connect the cold water supply

hose to a threaded 3/4 (gas)

connector, inserting the small

filter supplied with the

dishwasher and making sure

that it is fastened tightly in place

(see figure 2).

If the water pipes are new or

have not been used for an extended period of time, let the

water run to make sure that the water is clear and free of

impurities. If this precaution is not taken, there is a risk that

the water inlet can get blocked and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of 60°

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Drain Hose Connection

Fit the drain pipe into a drain

line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. Use the special

plastic elbow provided (see fi-

gure) to position it in the best

possible way. The part of the

pipe marked with the letter A

should be between 40 and

100 cm above the ground.

The pipe should not be immersed in water.

Attention: The special plastic hose support must be solidly

fastened to the wall to prevent the drain hose from moving

and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values

for the current in the home correspond to those on the

rating plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical

Service Centres for the replacement.

The plug

The dishwasher plug must be accessible even when the

appliance is installed as a built-in unit so that maintenance

can be done safely.

Fig.2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Indesit IDE1000 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Indesit IDE1000

Indesit IDE1000 User Manual - English - 80 pages

Indesit IDE1000 User Manual - English - 16 pages

Indesit IDE1000 User Manual - German, Dutch, French, Italian - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Indesit IDE1000 Manual

Product: