697351

In Lite CBL-25 14-2 Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
12 V CABLE
The operation of your in-lite system is largely determined by the type of
12 V cable you use and the way in which you lay it. This manual explains
the different types of in-lite cables and the options for installing them.
Please read the following instructions before installing.
You are advised to keep these installation instructions in a safe place.
Although a 12 V system is safe, we advise you to have a qualified
electrician check the installation.
Important!
Never connect the low-voltage cable directly to a 100-240 V power
source. It is only suitable for use in combination with a 12 V low-voltage
system. This product should only be used within the in-lite system. Use of
products other than those made by in-lite will invalidate the warranty.
Enjoy the lighting in your yard.
EN
Types of 12 V cable
There are two types of in-lite cables available: 14/2 and 10/2. The
distance the cable must cross in the garden determines the type of cable
you choose. A heavier cable is needed for longer distances. Therefore
always draw a cable plan first. We recommend you use only one type of
cable in a garden, also if you want to install several transformers (and
therefore make several cable plans for one garden). This will help
prevent mistakes that lead to the system not working correctly.
Options for laying 12 V cable
There are two types of cable plans or methods of laying cables: linear
and split. If you have made a lighting plan then making the wiring
diagram is just a question of drawing the cable onto the garden design.
Follow an imaginary line between the fixtures. Always test the circuit
above ground before you bury the cable underneath paving or soil.
Option 1: linear
Roll out the cable from the transformer into the garden and lead it to
the various armatures. The cable can end anywhere and can have the
following maximum length:
14/2 cable up to 40 m (Fig. 1A)
10/2 cable up to 80 m (Fig. 1B)
Does your lighting plan include fixtures with power greater than 35 W?
Always use the 10/2 cable for these.
Option 2: split
Roll out the cable from the transformer into the garden. Using the cable
connectors, make one or more branches that you lead to the various
fixtures. Ensure that the ridged and the smooth sides of both cables point
in the same direction. (Fig. 3)
The maximum length of the branch or branches depends on the place
where you install the cable connector or connectors. For each branch
first calculate the length of cable from the transformer to the relevant
cable connector. Subtract this length from the maximum cable length for
the cable you are using. The remaining number of metres is the maximum
length of the branch. You can make several branches as long as this total
does not exceed the maximum cable length:
14/2 cable up to 40 m (Fig. 2A)
10/2 cable up to 80 m (Fig. 2B)
Does your lighting plan include fixtures with power greater than 35 W?
Always use the 10/2 cable for these.
Important!
The maximum load of each cable connector is 50 W. If the total power of
the fixtures after the CC-2 is greater than 50 W, then multiple CC-2s must
be fitted. (Fig. 4). Always round up the number of cable connectors to be
used. (Fig. 5). Try to spread the power as evenly as possible along the
cable. This will benefit the light output.
Installation tips
Tip 1
Use plenty of cable for the installation. The cable will not then be under
tension if the garden subsides a little.
Tip 2
Insulate the cable ends with caps. You can do this by pulling the end
three centimetres of cable apart and putting a cap on each end. You do
not need to remove any insulation from the cable.
Tip 3
When connecting the fixtures leave plenty of cable from the fixture.
There are special extension cables (CBL-EXT CORD) of 1 metre and 3
metres available to increase the distance of the fixture to the main cable.
These are easy to install between the mini-connector on the fixture and
the mini-connector on the Easy-Lock (Fig. 6).
If after reading these instructions you have further question about
installing 12 V cable, please contact your dealer.
EN
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for In Lite CBL-25 14-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of In Lite CBL-25 14-2 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info