311702
2
Zoom out
Zoom in
Previous page
1/15
Next page
59
BEFORE USING THE WASHING MACHINE
1.Remove the packaging and check
a.
Cut and remove the shrink-wrap.
b.
Remove the top protection and the protective
corners.
c.
Remove the bottom protection by tilting and
turning the appliance on one rear bottom corner.
2.Remove the transport bracket
The appliance is fitted with transport screws and
a transport bracket to prevent damage during
transport.
Before using the washing machine
you must remove the transport bracket
(see
“Installation/Remove the transport bracket”).
Do not forget to screw back 4 screws to the rear
panel by which was fixed the transport bracket - to
avoid noisy and vibration of the machine.
3.Install the washing machine
Place the appliance on a flat and stable floor
surface.
Adjust the feet to ensure that the machine
is stable and level (see “Installation/Adjust
the feet”).
4.Water supply
Connect the water supply inlet hose in
accordance with the regulations of your local
water company (see “Installation/Connect the
water inlet hose”).
Water supply: Cold water only
Tap: 3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).
“For Great Britain & Ireland only:
Water inlet: hot and cold fill. The warm water
inlet temperature must not exceed 60° C.”
5.Drain hose
Connect the drain hose to the siphon or hook it
over the edge of a sink with the “U” bend (see
“Installation/Connect the water drain hose”).
If the washing machine is connected to a built-in
drainage system, ensure the latter is equipped
with a vent to avoid simultaneous loading and
draining of water (siphoning effect).
6.Electrical connection
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and the current
standard safety regulations.
The technical data (voltage, power and fuses) are
given on the rating plate on the rear of the
appliance.
The appliance must be connected exclusively by
means of a socket with an earth connection in
accordance with current regulations. The
appliance must be earthed by law. The
manufacturer declines all liability for damage to
persons or property deriving directly or
indirectly from failure to observe the directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing machine
disconnect it from the mains supply.
Access to the mains plug or to disconnection
from the mains supply via a double-pole switch
must be ensured at all times following the
installation.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
The appliance must be connected to an effective
earthing installation, in compliance with the
regulations in force. In particular, appliances installed
in premises containing a shower or a bath must be
protected by a differential residual current device of
at least 30 mA. Earthing the appliance is obligatory
under the law. The manufacturer declines all liability
for damage to persons or property deriving either
directly or indirectly from failure to observe the
directions above.
The washing machine may only be used in the
household for the prescribed uses.
Dimensions:
Width: 400 mm
Height: 900 mm
Depth: 600 mm
5gb10016.fm5 Page 59 Monday, July 16, 2001 12:11 PM
Black Process Plate
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis awv 516 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis awv 516 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis awv 516

Ignis awv 516 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info