Manual Ignis AWP 1406 (page 2 of 2) (English)

516613

Zoom out

Zoom in

1/2

Load the laundry, close the door and add detergents as

indicated on the front page and as described in the chapter

“Detergent and Additives” in your Instructions for Use.

1. Turn the programme selector to the desired

programme and temperature.

2. The time display shows the duration of the chosen

programme (in hours and minutes), and the “Start

(Pause)” indication lamp is flashing.

3. The indication lamp of the predefined spin speed

lights up.

If you do not start the programme soon after having

made your choice, the washing machine will switch off

automatically after about a quarter of an hour. Switch on the

washing machine again by turning the programme selector

back to “O” and then to the desired programme.

LOAD LAUNDRY, ADD DETERGENTS

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

Push the button of any option desired - the respective

indication lamp lights up. When the combination of

programme and additional option(s) is not possible, the

indication lights switch off automatically.

“Clean+” button

• Choose this option if you use an in-wash additive for

stain removal (powder, for example “Vanish”) - it will

optimize the additive’s efficiency to get better wash

performance and stain removal.

• Use with the maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together

with your detergent (only use powder detergent with this

option). Respect the manufacturer’s dosing instructions.

• May prolongs the programme by up to 15 minutes

• Appropriate for use of stain removers and bleaches

on oxygen basis. Chlorine or perborate bleaches

must not be used!

“Cold wash” button

• Saves energy used for water heating while maintaining

good wash result.

• Recomentable for lightly soiled laundry without stains.

• Make sure that your detergent is suitable for cold

wash temperatures (15 or 20 °C).

• Mainly selectable on the lowest temperature step of

the programmes.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helps people with

allergies.

“Easy ironing” button

• Reduces creasing by an increased water quantity and

a very gentle spin.

“Rinse hold” button

• The laundry remains in the last rinse water without

pregressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the door can be opened. As long as a

wash programme is running, the door remains locked and

must on no account be forced open. In case you have an

urgent need to open it during a running programme, refer to

“Cancel (Reset) a running programme before the end”.

PROGRAMME START

Open the tap and press the “Start(Pause)” button. The

indication lamp next to the “Start(Pause)” button lights

up. The programme sequence indicator shows the current

programme phase, running from left to right through Wash,

Rinse, Spin/Drain.

PROGRAMME END

The “Door open” indicator lights up, and the display shows

“End”. After about a quarter of an hour, the washing

machine will switch off completely to save energy.

1. Turn the programme selector to the “O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start(Pause)” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another spin

speed if you want.

3. Press the “Start(Pause)” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the end.

• Press and hold the “Reset” button for a few

seconds. Any existing water is drained out. It may last

some time until the door can be opened.

• The programme stops to “Rinse hold” at the time the

“Rinse hold” lights in the preogramme sequence

indication is on. The “Start/Pause” indicator blinks.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme will

terminate automatically with the final spin cycle for the

present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector to the “Drain” programme and press

the “Start/Pause” button.

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled

but intermediate spin peaks remain during the rinse.

The water is drained out only.

“Prewash” button

• Adds a prewash cycle to the wash programme selected;

prolongs the programme by about a quarter of an hour.

• Recommended for heavily soiled laundry (e.g. with sand

or granular dirt).

• Do not use liquid detergent for the main wash when

activating the “Prewash” option.

“Rapid” button

• Enables quicker washing by shortening the programme

duration.

• Recommendable for only lightly soiled laundry.

• Not selectable for Cotton 95°

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating “Start delay” option.

• Select programme, temperature and options.

• Press the “Start delay” button to select the delay time by

1 to 23 hours.

• Press the “Start(Pause)” button.

The countdown of the delay time begins; the “Start

delay” indication lamp and the dot on the display will

keep blinking until the programme starts.

• The time delay indication disappears when the

programme starts and it is replaced by the remaining

programme time.

• Once having pressed the “Start(Pause)” button,

the number of hours preselected can be reduced by

pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the “Start(Pause)” button:

• Turn the programme selector to another position or

press the “Reset” button.

..after having pressed the “Start(Pause)” button:

• Press the “Start(Pause)” - the start delay time

disappears from the time display.

START DELAY

FAILURE INDICATIONS

The time display shows the remaining programme time.

Due to variations in load and temperature of inlet water, the

remaining time is newly calculated in certain programme

phases. If this is the case, an animation appears on the time

display.

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

without “Rapid”

Approx. programme duration

(hours : minutes)

without “Rapid” with “Rapid”

Cotton 95 6.0 59** 1.90 2:00 -

Cotton 60 6.0 49 1.02 2:30 1:35

Cotton 40 6.0 54 0.65 2:00 1:15

Synthetics 60 3.0 50** 0.70 1:35 1:14

Synthetics 40 3.0 46 0.50 1:20 0:59

Delicates 40 1.5 50 0.65 0:50 -

Delicates 30 1.5 50 0.50 0:46 -

Daily load 40 3.0 45 0.45 1:00 -

Quick wash 30 3.0 40 0.30 0:30 -

Wool/Handwash 40 1.0 45 0.60 0:40 -

Wool/Handwash cold 1.0 45 0.10 0:35 -

Cotton

60°

* 60 6.0 49 0.78 4:00 -

Cotton

60°

* 60 3.0 37 0.69 2:20 *** -

Cotton

40°

* 40 3.0 37 0.58 2:30 -

Ignis is a registered trademark of Whirlpool USA.

5019 550 00002/A

CONSUMPTION DATA

Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water

supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through

the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy

consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the

programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting

Guide” in your Instructions for Use).

* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

*** Automatic adaptation of programme duration after detection of wash load

Power consumption in off-mode 0.16 W / in left-on mode 0.16 W

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Water tap closed”: no or not sufficient inlet water.

”Service”: failure or malfunction of an electrical

component.

”Clean pump”: waste water is not pumped out.

Spin speed on display blinks : unbalance during spinning.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AWP 1406 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AWP 1406

Ignis AWP 1406 Quick start guide - German - 2 pages

Ignis AWP 1406 Quick start guide - Dutch - 2 pages

Ignis AWP 1406 Quick start guide - French - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ignis AWP 1406 Manual

Product: