611543
9
Zoom out
Zoom in
Previous page
1/10
Next page
20
Direct drainage at the rear of the dryer
To avoid to empty the water container at the
end of each drying cycle, connect the pipe
supplied in the dryer directly to a fixed drain
or put it into a sink.
1. Remove the pipe in the lower part behind the
dryer and mount it to the plastic connector
(shown in driagram), put a rag underneath to
collect water spillage.
2. Connect the pipe supplied with the dryer to
the connector. The maximum drain height
is 1 m.
3. Make sure that the pipe is not bent or twisted
(the end of the pipe must not be immersed in
the drain water to avoid risk of siphoning).
The supplied hose length is 1,5 m.
The maximum permitted length is 2,5 m.
To change the direction of opening of the door
1. Unplug the dryer.
2. Open the door.
3. Remove the contact pin at the upper part of
the door with a spanner. Turn the contact pin
90° and take it out.
4. Unscrew the 2 screws at the door hinge and
remove the door.
5. To remove the door lock:
Unscrew the two screws above and below the
door lock system and slide it upwards (1,5 cm)
holding it from the bottom. Remove it.
6. To change the door opening:
Turn the door.
Re-fit the door with the 2 screws at the
preferred position.
Insert the door lock system at the opposite
side of the door and move it (1,5 cm) down.
Fix the 2 screws above and below the door
lock system
Take care not to reverse the sense of the
door lock system. The child safety must be
above the locking mechanism.
7. Replace the contact pin in the top of the door.
1. Wipe the cabinet with a mild household
detergent. Avoid using abrasive cleaners.
2. Clean the lint filter at the end of each drying
cycle.
3. If the lint filter mesh is clogged, clean it with
water and a soft brush.
4. Clean the heat exchanger at least every
three months proceeding as follows:
Open the door and press the button on the
bottom of the door entrance.
The heat exchanger flap opens.
Rotate the retaining springs and extract the
heat exchanger.
DRAINAGE SYSTEM
DOOR REVERSIBILITY
MAINTENANCE
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis AWL 261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AWL 261 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AWL 261

Ignis AWL 261 User Manual - German - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info