Manual Ignis AWF 595 IG (page 2 of 2) (English)

462091

Zoom out

Zoom in

1/2

5019 501 20009

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives”

in the Instructions for Use.

1. Turn the

programme selector

to the desired

programme.

Press the button(s) of any required option(s) - the

respective indicator lights up.

When the combination of programme and

additional option(s) is not possible,

the indicators switch off automatically. Unsuitable

combinations of options are deselected

automatically.

“Prewash” button

• Only for heavily soiled loads (e.g. sand, granular

dirt). Increases the cycle time by approx.

15 minutes.

• Do not use liquid detergent for the main wash

when activating the prewash option.

“Energetic wash” button

• This function increases the efficiency of the

detergent and prolongs the wash time, leaving

the set temperature unaltered.

“Rinse hold” button

• The laundry remains in the last rinse water

without the final spin cycle, to avoid creasing and

prevent colours from changing.

• This option is particularly recommended for the

“Synthetics”, “Daily load” or “Delicates”

programmes.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain

only.

• If you select “Rinse hold”, do not leave the

laundry to soak for too long.

Note:

The programme stops to “Rinse hold” at

the time the “Rinse Hold” light in the programme

sequence indicator is on. The indicator next to

the

“Start”

button flashes.

To terminate the “Rinse hold” option:

•Press the

“Start”

button; the programme will

terminate automatically with the final spin cycle

for the preset wash programme.

“No spin” button

• Pressing this button excludes spinning at the end

of the programme but the intermediate spin

cycles remain. With this option selected, drying

is automatically excluded.

Turn the knob to select the drying time, in automatic

mode (at end of wash cycle) or in manual mode,

selecting the “Drying” programme (with hand-

washed laundry). In the latter case it is necessary to

spin at a speed of at least 800 rpm. With the knob

turned to “0”, drying is not carried out.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. programme duration

(hours : minutes)

White Cotton / Antibacterial 90 5.0 52

1.70 2:10

Cotton 75 5.0 52 1.33 2:05

Cotton with “Eco”

***

60 5.0 49 0.95 2:15

Cotton 40 5.0 62 0.51 2:00

Synthetics 60 2.5 46

0.80 1:40

Synthetics 40 2.5 46 0.46 1:35

Daily load 40 3.5 52 0.30 1:25

Quick wash 35 2.5 30 0.40 0:40

Delicates 30 2.5 54 0.24 0:45

Wool 40 1.0 56 0.44 0:54

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption data

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household

conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference programme for energy label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

DRYING TIME

The “Start Delay” option allows you to programme

machine activation at a later stage, for example at

night when electricity is cheaper. Do not use liquid

detergent when activating the “Start delay”.

• Select the programme and options.

• Press the “Start Delay” button to select

programme start a delay time of 1 to 12 hours;

•Press the

“Start”

button.

The indicator next to the

“Start Delay”

button

lights up, whereas the selection indicator flashes

to signal the countdown of the remaining time.

• At the end of the delay time the machine starts

the set programme. The LED indicating the

wash stage in progress lights up.

• After pressing the

“Start”

, the number of hours

preselected can be reduced by pressing and

holding the “Start Delay” button.

To cancel the “Start Delay”:

Press the

“Start Delay”

button until all the

indicator lights are off. The selected programme will

then start.

Open the tap and press the

“Start”

button. After a

few seconds the

“Start”

button lights up, indicating

that the door is locked and the wash cycle has

started.

The “Start” button flashes when the wash cycle has

completed indicating that the door can now be

opened. As long as a wash programme is running,

the door remains locked and must not be forced

open. In case you have an urgent need to open it

during a running programme, refer to “Cancel

(Reset) a running programme before the end”.

• The “Start” button flashing indicates that the

programme has finished and the door is

unlocked.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Turn the programme selector to “Off/O”.

2. Select the new programme, any options and

another spin speed if you want.

3. Press the

“Start”

button again. The new

programme resumes the wash programme

from where the previous one was interrupted.

Do not add detergent for this programme.

• Reset by turning the programme selector to

“Off/0” and select the “Drain Spin” programme

to remove the water remaining in the bowl

before the door can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATOR

PROGRAMME END

CHANGING PROGRAMME AND/OR

OPTIONS AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

50120009GB.fm Page 2 Tuesday, September 18, 2007 10:22 AM

Black process 45.0° 150.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AWF 595 IG in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ignis AWF 595 IG

Ignis AWF 595 IG User Manual - English - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ignis AWF 595 IG Manual

Product: