109081
4
Zoom out
Zoom in
Previous page
1/4
Next page
10
Before calling After Sales Service:
1. Check to see if you can fix the problem
yourself (see “Troubleshooting guide”).
2. Switch off the hood for a few minutes and
re-start it to see if the problem has cleared itself.
3. If the malfunction persists, call
After-Sales Service.
Specify:
The nature of the problem.
The model.
The service code (number below
the word SERVICE on the rating
plate inside the hood behind the
grease filter).
Your full address.
Your telephone number and area code.
When installing the hood, the minimum distances from the cooktop must be respected, and
the numerical sequence and additional instructions must be followed exactly as indicated on
the Installation sheet.
EXTERNAL EXHAUST MODE
(
A
- see also instruction sheet)
Cooking fumes and vapours are conveyed
outside through a duct connected to the hood by
means of a collar.
The outlet duct diameter must be the same as
that of the collar.
If a flue-damper is to be installed, check that
it can open and close freely when installation
of the exhaust duct is complete.
The hood can be supplied with one (upper) or
two (upper and rear) exhaust outlet holes.
The hood is usually set up for using the
upper exhaust outlet.
1. The collar must be seated in the upper
exhaust outlet.
Use the rear exhaust outlet (where present).
1. Where fitted, remove the cover closing off the
rear outlet and collar.
2. Some models are fitted with a plastic
deflector that closes off the rear outlet.
If fitted, remove it.
3. Fit the collar in the rear outlet.
4. Put the cover (if fitted) in the upper outlet.
Warning!
If the hood has a carbon filter, this
should be removed.
Check that the switch inside the hood (if fitted)
is in position “A” Extractor; if not, set it to
this position.
AIR CIRCULATION MODE
(
F
- see also installation sheet)
The air is filtered by a carbon filter and recycled
into the surrounding atmosphere. The filtered air
is released towards the kitchen ceiling.
Warning!
If the hood does not have a carbon
filter, order one and fit it before use.
Check that the switch inside the hood (if fitted) is
on position “F” Filter; if not, set it to this position.
If the plug is provided, close off the upper
exhaust hole.
ELECTRICAL CONNECTION
Before connecting the hood, make sure the
voltage indicated on the rating plate corresponds
to the voltage in your home.
The plate is located inside the hood behind
the grille.
For GB this appliance is supplied without a plug
and is intended for direct connection to fixed
wiring in accordance with national wiring
regulations. An all-pole disconnection switch
with a minimum contact separation of 3 mm must
be included in the fixed wiring in an easily
accessible position.
The Manufacturer shall not be liable for
any damage or problem arising from
the failure to comply with the
above-mentioned instructions.
AFTER SALES SERVICE
INSTALLATION
75007Agb.fm5 Page 10 Monday, March 26, 2001 5:21 PM
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ignis AKS 626 IX RVS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ignis AKS 626 IX RVS in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info