506732
2
Zoom out
Zoom in
Previous page
1/2
Next page
- 2 - - 3
a-0,5 mb
ATTENTION! Read Carefully!
Before you install this luminaire, read this instruction manual carefully!
Introduction
Dear Valued Customer,
We thank you for the purchase of this quality product. This product is developed and constructed according
to the latest technical standards. The construction complies with the National and European Requirements
of the Low Voltage Directive and Electromagnetic Compatibility. The conformity was proven, relevant infor-
mation and documents are in the manufacturer’s possession..
In order to maintain conformity and ensure safe operation, strictly follow the operating instructions! They
contain important information regarding the operation and handling of this product. The provided information
should also be available to third parties in case you hand this luminaire to others. Therefore, please store
this manual safely.
Intended Use
This product is exclusively approved for use with 230 V / 50Hz alternating voltage, and only in combination
with specified bulbs types (see the section entitled "Specifications").
This product is non-dimmable.
This product is permitted for indoor use only.
The luminaire is suitable for mounting on normal flammable surfaces and therefore supplied
with the F-mark.
Avoid moisture, dirt and excessive heat while installing and during operation.
Use only the type of bulb as mentioned in the section "Technical Data".
It is not permitted to change or rebuild the luminaire set.
A different use than described above leads to damage of this product. Beyond that, it can create hazards,
such as short circuit, fire, electrical shock, etc.
The safety instructions and technical data must be observed without fail!
Safety Reference
Pay close attention to this manual’s safety warnings.
Keep this manual close by to have it ready when needed.
When passing the product to a third party, be sure to include the manual.
Before connecting to the mains supply, ensure that the supply voltage and current comply with the
information on the rating plate.
The luminaire complies to protection class II, and must not be connected to the protective conductor.
Always ensure that the power supply is cut off before mounting the product, replacing bulbs, or any other
work on the luminaire.
Wearing any metal or other conductive jewelery such as chains, bracelets and rings is forbidden during any
workings on the luminaire, including cleaning!
The minimum allowable distance between the light source to any illuminated surface is 50 cm.
I
ATTENTION: Do not use this lamp as a bed lamp, and do not use this lamp flammable textile. Do not put
the supply cable across the head, because the bulb becomes very hot when switched on.
Never cover the luminaire with heat-insulating materials.
Do not attach any other products or decorations to the lamp.
Do not insert any metallic objects into the lamp’s interior.
Do not use the luminaire in rooms and adverse suroundings where flammable gases, vapors, or dusts exist
or might exist.
Do not exceed the maximum wattage per bulb.
To avoid fire and eye damage, please note the following:
- Never look into the light, and never direct aim the beam at persons or animals.
- Keep the luminaire away from flammable materials and objects!
In commercial facilities, the accident prevention regulations for electrical installations and equipment of the
commercial Accident Prevention & Insurance Association , must be strictly followed.
Cut the power supply completely and provide a safeguard to prevent reconnection in case of damages of any
kind, particularly in wet conditions when a safe operation is no longer ensured.
Only qualified persons may conduct repairs, original spare parts are required.
Mounting Assembly
Remove all packaging material.
Before installation, check the lamp for damage.
Only connect power once installation is complete.
The safety instructions and relevant technical data must be observed under all circumstances!
First plan the fixing position for the lamp, and ensure the availability of a 230 V outlet within 1.80 m distance.
I
ATTENTION: Please do not clamp this Lamp to tubular items, as they do not provide sufficient hold.
Proceed with the assembly according to the following steps:
Remove the mounting ring from the lamp holder using the supplied tool.
Put the lampshade on the lamp holder, replace the mounting ring, and screw them tight using the supplied
tool.
Insert the supplied bulb into the socket.
Clamp the luminaire to the mounting surface (clamp thickness 15 mm to 25 mm).
Confirm the safe hold of the lamp.
Adjust the desired light angle and direction while observing the minimum distance to any illuminated surface.
Connect the Euro plug with the outlet and turn on the Switch. The lamp is ready for use.
Mounting Drawing
d
h
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ideen Welt KL-G904 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ideen Welt KL-G904 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info