12320
62
Zoom out
Zoom in
Previous page
1/64
Next page
15
60
INSTALLATION NOTES
For amateur base station installations, it is
recommended that the forwards clearance in front of
the antenna array is calculated relative to the EIRP
(Effective Isotropic Radiated Power). The clearance
height below the antenna array can be determined in
most cases from the RF power at the antenna input
terminals.
As different exposure limits have been recommended
for different frequencies, a relative table shows a
guideline for installation considerations.
Below 10 MHz, the recommended limits are specied
in terms of V/m or A/m elds as they are likely to fall
within the near-eld region. Similarly, at antennae may
be physically short in terms of electrical length and that
the installation will require some antenna matching de-
vice which can create high intensity magnetic fields.
Analysis of such MF installations is best considered in
association with published guidance notes such as the
FCC OET Bulletin 65 Edition 97-01 and its annexes
relative to amateur transmitter installations. Further in-
formation can be found at http://www.arrl.org/
Typical amateur radio installation
Exposure distance assumes that the predominant ra-
diation pattern is forwards and that radiation vertically
downwards is at unity gain (sidelobe suppresion is
equal to main lobe gain). This is true of almost every
gain antenna today. Exposed persons are assumed to
be beneath the antenna array and have a typical
height to 1.8 m.
The gures assume the worst case emission of con-
stant carrier.
For the bands 10 MHz and higher the following power
density limits are recommended :
1030 MHz 2 W/sq m
Watts (EIRP)/ Clearance heights
1 2.1 (m)
10 2.8
25 3.4
100 5
1000 12
Watts (EIRP)/ Forward clearance
100 2 (m)
1,000 6.5
10,000 20
100,000 65
In all cases any possible risk depends on the transmit-
ter being activated for long periods. (actual recom-
mendation limits are specified as an average of 6
minutes) Normally the transmitter is not active for long
periods of time. Some radio licenses will require that a
timer circuit automatically cuts the transmitter after 12
minutes etc.
Similarly some types of transmitter, SSB, CW, AM, etc.
have a lower average output power and the perceived
risk is even lower.
Versions of the IC-718 which display the CE
symbol on the serial number seal, comply with
the essential requirements of the European
Radio and Telecommunication Terminal Direc-
tive 1999/5/EC.
This warning symbol indicates that this equip-
ment operates in non-harmonised frequency
bands and/or may be subject to licensing con-
ditions in the country of use. Be sure to check
that you have the correct version of this radio or
the correct programming of this radio, to com-
ply with national licensing requirement.
IC-718.qxd 02.9.6 14:30 Page 60
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-718 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-718 in the language / languages: English as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info