Manual I-onik WS-103 (page 2 of 2) (German)

521909

Zoom out

Zoom in

1/2

hometec

WS-103

Quick Start Guide

Motion Sensor

English

Please keep these instructions in a safe place for future

reference.

Kit Contents:

1x i.onik

Motion Sensor

1x Ball-head joint mounting bracket

3x Screws and wall plugs

1x Instruction leaet

1. Introduction

The i.onik

Motion Sensor is designed to trigger the i.onik

Alarm-

system Smart Panel when it senses movement in a given area.

Note:

Where pets are in the home it is advised that they are not

allowed onto higher surfaces (above 1 m in height) where they

may trigger the sensor.

2. Location

First determine the location of the Sensor, which should be placed:

• On a solid surface between 1.8 m to 2.4 mm (6 ft to 8 ft) from the

oor.

• Near key entry/exit points.

• Away from extreme temperature sources (radiators, ovens, stoves

etc.) and large metal objects that could interfere with the wireless

performance.

• Away from direct sunlight.

• Indoors only and not behind partitions.

• Where better transmitter/reception performance can be achieved

(if necessary).

3. Installation and Operation

3.1 Powering up the Motion Sensor

• Remove the battery cover, insert and connect a

9 V battery as shown in diagram below and

replace the cover (Requires 1x 9 V battery).

• Low battery indication: If the batteries need to

be replaced, the RED LED will ash (not inclu-

ding entry/exit delay ashing).

3.2 Installing the Motion Sensor

• Hold the enclosed mounting template against the wall at the selected

location and mark the points for drilling.

• Drill the holes and insert wall plugs.

• Attach the bracket to the mounting surface with the screws provided.

• Attach the Motion Sensor to the mounting bracket.

3.3 Sensor Sensitivity

IMPORTANT! The Motion Sensor is designed with a power saving

program and will remain inactive for 3 minutes after each detection.

Please bear this in mind during system set up.

The sensitivity of the Motion Sensor is adjustable and can be chan-

ged by setting the connector on either the “High”, “Middle” or “Low”

position. When the sensitivity is set to “Low”, more movement is

required to trigger the sensor. It is recommended to set the sensitivity

to “Low” and perform a “Walk Test” (described in section 3.4). If the

walk test result is satisfactory, the sensitivity does not require further

adjustment. If the walk test result shows the sensitivity is too low,

then the sensitivity can be set to “Middle” or “High” as required. It

is recommended that a walk test be conducted after each change in

sensitivity setting.

3.4 Walk test

After mounting the sensor at the desired location,

it is important to perform a walk test in order to

determine if the sensor is detecting the correct

area. The distance at which the sensor can detect

motion can be adjusted by altering the angle of the

sensor. To reduce the detection range, simply move

the sensor downward and move the sensor upward to maximize

the range.

Note:

Enter into ALERT mode before you perform the walk test, so

that the alarm is not triggered.

You should walk in the area that you would like the sensor

to monitor. If movement is detected the red light inside the

unit will appear. If the red light does not appear, adjust the

mounting angle accordingly. Perform the walk test again after

3 minutes. Repeat this procedure until motion is detected.

Whilst carrying out the test, there should be no movement in

the detection area during the 3 minute interval.

Tips:

The sensor should not face towards direct sunlight, be placed near

heat or cold producing devices (i.e. air conditioning, radiators, fans,

ovens, heaters etc.) that may cause false triggers. Also perform the

walk test in areas which the sensor is not intended to cover, to ensure

movement cannot be detected.

4. House Security Code Settings

Unless the factory settings of the i.onik

Alarmsystem Smart Panel

have been altered, the House Security Code will NOT need to be chan-

ged. However, if the settings on the Smart Panel have been altered,

or need to be altered to solve the problem of the Smart Panel and

sensors activating intermittently (or not working at all) or interference

with other systems, then the House Security Code on all system mo-

dules (sensors and sirens) will also need to be changed.

House Security Code settings can be altered as follows:

• There are 4 jumpers or dip-switches on each device.

• Remove the jumper compartment cover, then pull out or plug the

jumper into the contacts to change the House Security Code

• If a jumper is plugged it is ON if it is removed it is OFF. Default code

is with all the jumpers plugged.

• To ensure the system works correctly, make sure the jumpers on

the Smart Panel and all other system modules (sensors and sirens)

match exactly.

5. Zone Code Settings

The sensor is supplied with a pre-assigned Zone setting. The sensor

can be assigned to a different zone as follows:

• Unscrew and remove the battery compartment cover on the rear of

the sensor.

• In the area marked “Zone Code” there are eight pairs of metal con-

tacts with a number next to each.

• The number corresponding to the pair of contacts which is plugged

with a jumper is the current zone.

• To re-assign to a different zone, simply unplug the jumper from its

current zone and plug it across the contacts corresponding to the

new zone number selected.

6. Maintenance

The product may be cleaned with a soft damp cloth and then wiped

dry. Do not use abrasive, solvent based or aerosol cleaners as this

may damage and/or discolour the product.

Do not allow water to enter or attempt to clean inside the unit.

7. Batteries

Do not allow the batteries to corrode or leak as this may cause per-

manent damage to the product. Take care to insert the batteries with

the correct polarity as shown inside the battery compartments. Do not

mix new and old batteries or different types of batteries. Do not use

rechargeable batteries.

At the end of their useful life the batteries should be disposed of

via a suitable recycling centre. Do not dispose of with your normal

household waste. DO NOT BURN.

8. Alarm System Limitations

Even the most advanced alarm systems cannot guarantee 100 % pro-

tection against burglary or environmental problems. All alarm systems

are subject to possible compromise or failure-to-warn for a variety of

reasons.

Please note that you may encounter problems with your system

if:

• The Smart Panel is not placed within hearing range of persons slee-

ping or remote parts of the premises.

• The sensors are placed behind doors or other obstacles.

• Intruders gain access through unprotected points of entry (where

sensors are not located).

• Intruders have the technical means of bypassing, jamming,

or disconnecting all or part of the system.

• The power to the sensors is inadequate or disconnected.

• The sensors are not located in proper environmental/temperature

conditions i.e. too close to a heat source.

Note:

Inadequate maintenance is the most common cause of alarm

failure; therefore, test your system at least once per week to

be sure the sensors and sirens are working properly.

Although having an alarm system may make you eligible for

reduced insurance premiums, the system is no sub-stitute for

insurance.

Chips and More GmbH

Gewerbestr. 7 | 79112 Freiburg | Germany | www.i-onik.de

Service: + 49 7664 403 69 12

Email: support@i-onik.de

Weitere Informationen und Erklärungen zur Handhabung des Alarmsystems finden Sie unter www.i-onik.de

For more details and questions on how to operate the alarm kits, please go to www.i-onik.de

Move the sensor

downward to reduce

the range.

Move the sensor

upward to maximize

the range.

Jumpers for house security code - Smart Panel

- Each sensor

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

*Jumper:

ON = Plugged,

OFF = Pull Out

Dip-Switches for house security code

- Key Fob Remote

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

Jumpers for zone code Default zone code: Zone 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of I-onik WS-103 in the language / languages: German as an attachment in your email.

The manual is 0,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

I-onik WS-103 Manual

Product: